Q1. Refer to the Exhibit. -- Exhibit --

-- Exhibit --

An administrator has created the resource pool configuration shown in the Exhibit. 

Based on the exhibit, which virtual machine(s) can be successfully powered on? 

A. VM-M1 only 

B. VM-K1 only 

C. VM-K1 and VM-K2 only 

D. VM-K1, VM-K2, and VM-M1 

View Answer

Q2. From which two locations in the inventory hierarchy can you deploy a virtual machine using a template? (Choose two.) 

A. Directly from the template. 

B. From a compute resource. 

C. From an existing virtual machine. 

D. From a Datastore. 

View Answer

Q3. An administrator needs to verify that vMotion operations can be performed in a vSphere data center. 

What round trip time (RTT) latency is the maximum value that will allow vMotion operations to succeed? 

A. 50ms RTT 

B. 100ms RTT 

C. 150ms RTT 

D. 200ms RTT 

View Answer

Q4. What is the default load balancing policy for a newly created VMkernel port on a vSphere Distributed Switch? 

A. Route based on orginating virtual port ID 

B. Route based on IP Hash 

C. Route based on source mac address 

D. Route based on physical NIC load 

View Answer

Q5. An administrator is using the Host Failures to Tolerate Admission Control Policy for a vSphere High Availability (HA) cluster. When configuring this setting on the cluster, the administrator sees this error message: 

Insufficient resources to satisfy HA failover level on cluster 

What are two likely causes for the error? (Choose two.) 

A. The hosts in the cluster are disconnected. 

B. A host in the cluster is displaying an HA error. 

C. Distributed Resource Scheduler has not been configured on the cluster. 

D. Virtual Machine Component Protection has not been turned on. 

View Answer

Q6. You need to add an object to an existing vApp using the vSphere Web Client. How is this accomplished? 

A. Create an Object Inside the vApp. 

B. Add an Object to a vApp. 

C. Add an Object to the Datastore the vApp is located in. 

D. Move all Objects to a new Datastore folder. 

View Answer

Q7. Refer to the Exhibit. 

An administrator has configured a host profile so that ESXi 6.x hosts will point to the corporate NTP server for time synchronization. The NTP server is located at 10.0.30.213, but time has not been synchronized properly across the ESXi hosts. 

The administrator reviews Host Profile settings as shown in the Exhibit. 

Which two steps are required to resolve the issue? (Choose two.) 

A. Correct the NTP server IP address. 

B. Check the host for host profile compliance. 

C. Remediate the host based on the updated host profile. 

D. Change the NTP server to the FQDN as IP Addresses are not supported. 

View Answer

Q8. An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. 

Where is the ESXi host IP address configured? 

A. RVC console 

B. Direct Console User Interface 

C. vSphere Web Client 

D. vSphere Client 

View Answer

Q9. Which three actions can be taken as a result of executing the vSphere Update Manager 6.x scan and remediation wizards? (Choose three.) 

A. Install and upgrade software in virtual machines. 

B. Upgrade the firmware on ESXi host devices. 

C. Upgrade and Patch ESXi hosts. 

D. Install and update third-party software on hosts. 

E. Upgrade virtual machine hardware. 

View Answer

Q10. An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. 

How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? 

A. Set the shares of the priority virtual machine to High and the rest to Low. 

B. Set the shares of the priority virtual machine to High. 

C. Set the shares of the priority virtual machine to High and the rest to Normal. 

D. Set the shares of the priority virtual machine to Normal and the rest to Low. 

View Answer