NEW QUESTION 1
When provisioning the redundancy-configuration, the peer name for each of the peers in a High Availability configuration must also be defined in each system’s ______.

• A. hostname parameter under the sip-configconfiguration element
• B. hostname parameter under the account-config configuration element
• C. hostname parameter under the bootparam configuration branch
• D. target name parameter under the bootparam configuration branch
• E. hostname parameter under the system-config configuration element

Answer: E

NEW QUESTION 2
You finished configuring a not Real Time Change (not RTC)-supported configuration element and you want to apply the change in your service.
Which two options are valid in order toaccomplish this? (Choose two.)

• A. From user mode, execute the save-config and activate-config commands.
• B. From configuration mode, execute the save-config, activate-config, and reboot commands.
• C. From superuser mode, execute the save-config and activate-config and reboot commands.
• D. From superuser mode, execute the save-config and activate-config commands.
• E. From superuser mode, execute the save-config, activate-config, and reboot force commands.

Answer: AD

NEW QUESTION 3
You are adding peers to a Policy-Based Realm Bridging (PBRB) configuration. Which two configuration steps, among others, are required? (Choose two.)

• A. Navigate to the media-manager configuration branch and configure the realm-config configuration element.
• B. Navigate to the session-router configuration branch and configure the sipd-address configuration element.
• C. Navigate to the session-router configuration branch and configure the local-policy configuration element.
• D. Navigate to the session-router configuration branch and configure the sip-nat configuration element.
• E. Navigate to the media-manager configuration branch and configure the access-control configuration element.

Answer: AE

NEW QUESTION 4
Whichtwo statements are true about SIP response code handling on the Session Border
Controller? (Choose two.)

• A. The Session Border Controller will originate a 503 when there are no steering pool ports available.
• B. The Session Border Controller will originate a 403 response when bandwidth allocated to a realm has been exhausted.
• C. The Session Border Controller cannot originate 3xx class redirect responses.
• D. By default, the Session Border Controller will recurse on the 6xx messages.
• E. The Session Border Controller can transmit a different SIP response code than it received.

Answer: AC

NEW QUESTION 5
Examine the output below from the show sipd invite command:

How many 600 Busy Everywhere messages sent by the Session Border Controller in the last 140 seconds did not originate from a downstreamdevice?

• A. 157
• B. 13
• C. 4
• D. 161

Answer: B

NEW QUESTION 6
You are troubleshooting a SIP routing issue and you haveaccess to the SIP call ow processed by the Session Border Controller.
Which two steps are valid for troubleshooting this type of issues? (Choose two.)

• A. It is necessary to locate the SIP session to troubleshoot and check if there is a 404 Routes Not Found SIP error message.
• B. It is recommended to look for 183 Session Progress SIP error messages that indicate routing issues.
• C. It is recommended to check the called number by looking at the Request-URI of the INVITE message and making sure it is a validnumber to be routed.
• D. It is recommended to find the CANCEL method received by the Session Border Controller which typically identifies a SIP routing issue.
• E. It is necessary to find an initial INVITE received by the Session Border Controller which getsa 503 Service Unavailable SIP error message.

Answer: BE

NEW QUESTION 7
Which configuration step is required to route a SIP callbased on the value of the SIP INVITE Request-URI?

• A. Navigate to the policy-attribute configuration element and configure the from-address parameter to match the Request-URI value.
• B. Navigate to the policy-attribute configuration element and configure the to-address parameter to match the Request-URI value.
• C. Navigate to the local-policy configuration element and configure the from-address parameter to match the Request-URI value.
• D. Navigate to the local-policy configuration element and configure the to-address parameter to match the Request-URI value.
• E. Navigate to the local-policy configuration element and configure the destination-address parameter to match the Request-URI value.

Answer: C

NEW QUESTION 8
What do you need to do to support ftp service on a media interface?

• A. Add the IP address of the remote device to the hip-ip-list and ftp-address parameters.
• B. Set the ftp-address parameter to enabled.
• C. Add the IP address of the interface in the hip-ip-list and ftp-address parameters.
• D. Set the hip-address parameter to enabled.
• E. Add the IP address of the interface in the hip-ip-list and telnet-address parameters.

Answer: B

NEW QUESTION 9
You need to configure the Session Border Controller toperform load balancing between two downstream SIP proxies.
Which option shows the configuration elements that you should configure for the load balancing feature?

• A. session-router and router-group
• B. realm-config and enum-group
• C. group-policy andload-policy
• D. proxy and proxy-pool
• E. local-policy and session-group

Answer: A

NEW QUESTION 10
CORRECT TEXT
Which statement is true about the Host In Path (HIP) feature In the Session Border Controller?

• A. By default, theSession Border Controller's FTP, ICMP, SNMP, and Telnet services cannot be accessed via the management interfaces.
• B. To enable these services (FTP ICMP, SNMP, and Telnet services), the enable host-in-path command must be executed from the superuser mode.
• C. To enable these services, the Session Border Controller includes a software license that enables administrative traffic over the media interfaces.
• D. By default, the Session Border Controller's FTP, ICMP, SNMP, and Telnet services cannot be accessed viathe media interfaces.
• E. These four fields (FTP, ICMP, SNMP, and Telnet services) are collectively known as the Host Interface Priority.

Answer: A

Explanation:
Reference https://docs.oracle.com/cd/E52358_01/doc/sbc_scx620_acliconfiguration.pdf

NEW QUESTION 11
You wantto configure the maximum duration in seconds of any session in the Session Border Controller.
How would you accomplish this?

• A. Navigate to the media-manager configuration element and configure the max-signaling- bandwidth parameter.
• B. Navigate to the media-manager configuration element and configure the flow-time-limit parameter.
• C. Navigate to the sip-config configuration element and configure the operation-mode parameter.
• D. Navigate to the sip-config configuration element and configure theflow-time-limit parameter.
• E. Navigate to the media-manager configuration element and configure the latching parameter.

Answer: C

NEW QUESTION 12
You are configuring access rules in a Session Border Controller Peering architecture. Which configuration step is required to allow access from any User Agent (UA)?

• A. Navigate to thesip-port configuration element and set the allow-anonymous parameter to all.
• B. Navigate to the realm-config configuration element and set the addr-prefix parameter to the IP subnet of your trusted User Agent (UA).
• C. Navigate to the sip-port configurationelement and set the allow-anonymous parameter to address-prefix.
• D. Navigate to the session-agent configuration element and set the ip-address parameterto the IP subnet of your trusted User Agent (UA).
• E. Navigate to the sip-port configuration element and set the allow-anonymous parameter to agents-only.

Answer: A

NEW QUESTION 13
Which statement is true about Session Border Controller architectures andrealm bridging?

• A. The Hosted NAT Traversal (HNT) architecture focuses on the border point between two different service provider networks, both in the home realm.
• B. The Hosted IP architecture focuses on the border point between one enterprise network realm and one service provider network realm.
• C. The Access-backbone architecture focuses on the border point between two backbone realms.
• D. The Peering architecture focuses on the border point between two different service provider networks and theirrealms.
• E. The Gateway architecture Focuses on the border point between one enterprise network realm and one service provider network realm.

Answer: B

NEW QUESTION 14
Which SIP headers in an incoming SIP message to the Session Border Controller are used by a local-policy configuration element for routing?

• A. From and To headers
• B. From header and Request-URI
• C. Call-Id header
• D. Contact header
• E. Via and To headers.

Answer: D

NEW QUESTION 15
Which configuration step is correct for a phy-interface configuration element used for signaling and/or media?

• A. A phy-interface elementmust be configured for each interface used for High Availability(HA) heartbeats, but not for signaling and/or media.
• B. After configuring a phy-interface configuration element for signaling and/or media, a reboot of the Session Border Controller is required.
• C. A phy-interface configuration element must be configured for each interface used.
• D. A unique phy-interface configuration element is created for all signaling/media interfaces.
• E. A phy-interface configuration element for signaling and/or media hasthe operation-type parameter set to control.

Answer: B

NEW QUESTION 16
Which three options are valid ways to apply Header Manipulation Rules (HMRs) to your existing configuration?

• A. Navigate to the network-interface configuration element and configure the in- manipulationid parameter.
• B. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.
• C. Navigate to the sip-interface configuration element and configure the in-manipulationid parameter.
• D. Navigate to the session-agent configuration element and configure the in-manipulationid parameter.
• E. Navigate to the session-group configuration element and configure the in-manipulationid parameter.

Answer: ABC

NEW QUESTION 17
Which two statements are correct about configuring realms and their corresponding interfaces? (Choose two.)

• A. You can associate multiple home realms with a single network interface.
• B. You can configure more than one SIP interface per realm.
• C. Although you can use both TCP and UDP concurrently as the transport protocol, youcan only have one SIP interface per realm.
• D. You can associate multiple realms with a single networkinterface.
• E. You can associate multiple network interfaces with a single realm only when either TCP or UDP is used as the transport protocol.

Answer: CD

NEW QUESTION 18
To return the Session Border Controller configuration to a known, factory default state, you must ____.

• A. press the reset button on the front panel
• B. issue the delete-configcommand
• C. issue the set-system-state offline command
• D. issue the set-system-state offline
• E. issue the delete-config and reboot commands

Answer: E

NEW QUESTION 19
You are configuring the boot parameters in the Session Border Controller. Which three statements are true about the boot parameters? (Choose three.)

• A. A reboot is always required to apply any change to the boot parameters.
• B. The target name is usedfor domain name resolution.
• C. The system clock is a boot parameter.
• D. The boot parameters are stored in Non-Volatile Random Access Memory (NVRAM).
• E. The boot parameters are not affected by the activate-config command.

Answer: ACD

NEW QUESTION 20
What configuration step is required for booting the SessionBorder Controller from an external FTP server?

• A. Navigate to the bootparams configuration branch and set the host inet field to the IP address of the external BOOTP Server from which the Session Border Controller can boot.
• B. Navigate to the system configuration branch and set the ip address field of the wancom1 management interface.
• C. Navigate to the bootparams configuration branch and set the ip address field of the destination SIP device with which the Session Border Controller needs to interact.
• D. Navigate to the system configuration branch and set the ip address field of the wancom0 management interface.
• E. Navigate to the bootparams configuration branch, set the host inet or Host IP, FTP username, and FTP password for the external FTP Server in which the image file resides.

Answer: C

NEW QUESTION 21
You made a configuration change to a media interface.
Which command must be executed to commit the change to volatile (RAM) memory?

• A. From configuration mode, execute the done command.
• B. From superuser mode, execute the write-config command.
• C. From user mode, execute the save-config command.
• D. From user mode, execute the commit-config command.
• E. From superuser mode, execute the save-config command.

Answer: A

Explanation:
Reference http://www.oracle.com/webfolder/technetwork/acmepacket/Additional%20Technical%20Sol ution%20Documentation/SFB%20video%20ESBC.pdf

NEW QUESTION 22
In which two ways can you remove support for telnet from a media interface? (Choose two.)

• A. Navigate to the network-interface configuration element and run the delete-hip-ip <IP address> command.
• B. Navigate to the phy-interface configuration element and run the remove-hip-ip <IP address> command.
• C. Navigate to the network-interface configuration element and run the remove-telnet-ip <IP address> command.
• D. Navigate to the network-interface configuration element and run the remove-hip-ip <IP address> command.
• E. Navigate to the phy-interface configurationelement and run the remove-telnet-ip <IP address> command.

Answer: AC

NEW QUESTION 23
When setting up the registration-caching parameter to enabled in the sip-interface configuration element, _______.

• A. the Session Border Controller will never use the SIP-NAT mechanism for routing
• B. the Session Border Controller will not use the registration cache for routing
• C. all endpoints in the realm will be cached when registered
• D. only endpoints behind NAT in the realm will be cached when registered
• E. the Session Border Controller will never use the local-policy mechanism for routing

Answer: A

NEW QUESTION 24
......