NEW QUESTION 1
When a Layer 2-only networking topology is deployed, what is the behavior of the ACP 4200?

• A. It will support only a single management VLAN.
• B. It will extend VLANs out to the Data Center routers which will provide Layer 3 routing.
• C. It will support only a single application VLAN.
• D. It will have 802.1Q tagging enabled on all ports of the VSP switches.

Answer: B

NEW QUESTION 2
What is the purpose of VMware vMotion as used in ACP 4200?

• A. It enables an operational virtual machine to migrate from one ESXi host to another, which includes its running state and storage.
• B. It dynamically allocated and balances computing capacity across the logical resource pools.
• C. It provides monitoring of operating system and hardware failures, and also restarts virtual machines on other hosts within the resource pool.
• D. It creates a pool of virtual disk space that can be shared by multiple virtual machines.

Answer: A

NEW QUESTION 3
A customer experienced an outage of one of their Host servers in their ACP 4200 solution. Additionally, after the failure, all of the applications that were running on the failed host, did not recover to another host.
To verify the configuration, which third party management tool needs to be used?

• A. SSH into the switches
• B. Avaya Orchestrator
• C. Nimble Storage web interface
• D. vSphere Web Client

Answer: D

NEW QUESTION 4
Which three tasks must be performed by the ACP 4200 implementation team at the customer site? (Choose three.)

• A. Connect the network switches to the customer network.
• B. Assign IP addresses to the existing Virtual Machines.
• C. Connect to the VMware vCenter Server Appliance and power up the virtual machines.
• D. Fill up the IP template.
• E. Install a ground connection for each enclosure.

Answer: ADE

NEW QUESTION 5
In which two situations does the Customer and Network Lifecycle workbook need to be updated? (Choose two.)

• A. On the 31st of January every year, even if no changes have been made to the ACP 4200.
• B. When an ACP 4200 component password is changed.
• C. When a new Administrator is given access to the ACP 4200.
• D. When a new host server is added to the ACP 4200.

Answer: BD

NEW QUESTION 6
Using VMware networking in ACP 4200, how are Virtual NICs mapped to physical NICs?

• A. Via DRS rules
• B. On a 1-to-1 basis
• C. Via Virtual Switches and Port Groups
• D. Via the VNIIC mapping tables

Answer: D

NEW QUESTION 7
Why does enabling VMware Enhanced vMotion Compatibility (EVC) prevent vMotion migrations from falling?

• A. Because of incompatible DRS rules across the cluster
• B. Because of incompatible HA rules across the cluster
• C. Because of insufficient memory across the cluster
• D. Because of incompatible CPUs across the cluster

Answer: D

NEW QUESTION 8
An Avaya Orchestrator administrator is asked to check the CPU usage for the last 24 hours of one of the ESXi Hosts, as it has been performing erratically.
How can the administrator go about doing this?

• A. By clicking on the Compute Group's Service State line.
• B. By navigating to Quick View – All Host Problems.
• C. By going to the Performance Graphs of the CPU Usage Service for the host.
• D. By selecting the VM Group's Service State line.

Answer: A

NEW QUESTION 9
What is the purpose of the VMware Distributed Resource Scheduler (DRS) as used in ACP 4200?

• A. It enables a utility that balances computing workloads with available resources in a virtualized environment.
• B. It enables an operational virtual machine to migrate from one ESXi host to another, which includes its running state and storage.
• C. It provides monitoring of operating system and hardware failures, and also restarts virtual machines on other hosts within the resource pool.
• D. It creates a pool of virtual disk space that can be shared by multiple virtual machines.

Answer: A

NEW QUESTION 10
An engineering implementation team has been asked to install an ACP 4200.
Which task related to the Avaya Orchestrator is completed during the installation by the implementation team?

• A. Deploy the Rack and Device Dashboards.
• B. Install Avaya Orchestrator.
• C. Run the ACP Configuration Wizard.
• D. Power on the Avaya Orchestrator virtual machine.

Answer: B

NEW QUESTION 11
Refer to the exhibit.

What is the purpose of the “SMRule” DRS rule that states the two Avaya Aura® Session Managers must run off different ESXi hosts?

• A. To improve the latency of DRS load-balancing
• B. To prevent a single ESXi host from being overloaded with SIP traffic
• C. To preserve seamless failover/recovery across primary and secondary Session Managers
• D. To reduce the memory and CPU load on a single ESXi host

Answer: C

NEW QUESTION 12
Refer to the exhibit.

In the deployment shown in the exhibit, how is High Availability achieved across the two Data Centers?

• A. By ensuring that the L2 VLANs are extended across to both Data Centers.
• B. By managing both Data Centers using the same vCenter Server and using vMotion and DRS.
• C. By using Virtualization Provisioning Service (VPS) to automate the provisioning of the network hardware and vSwitches across the two Data Centers.
• D. By using Avaya Aura® Application High Availability features.

Answer: C

NEW QUESTION 13
Avaya Orchestrator monitors the ACP 4200 components by organizing them into which two groups? (Choose two.)

• A. Power
• B. Virtual Machines
• C. Storage
• D. Applications

Answer: AC

NEW QUESTION 14
With ACP 4200, what is mandatory to ensure Avaya Aura® High Availability across the two Data Centers?

• A. A single vCenter Server that manages both Data Centers.
• B. Network connectivity to and in between the two Data Centers.
• C. Identical compute servers in both Data Centers.
• D. The same VLANs in both Data Centers.

Answer: A

NEW QUESTION 15
When new VMs are added the ACP 4200, which action is mandatory?

• A. The new VMs must be configured to send SNMP Traps to Avaya Orchestrator.
• B. CPU and Memory reservations must be manually configured to the application recommendations for the new VMs.
• C. Avaya Orchestrator must be configured to recognize the new VMs.
• D. ACP Configurator Tool must be used to calculate resource availability for the ACP to support the new VMs.

Answer: A

NEW QUESTION 16
How would an administrator display the IP addresses of the VSP switches of the ACP 4200 within the Avaya Orchestrator Home Dashboard?

• A. By right-clicking on the Dashboard menu item and downloading the network summary report.
• B. By right-clicking on the Admin menu item and downloading the network summary report.
• C. By right-clicking on the Report menu item and downloading the network summary report.
• D. By hovering the mouse pointer over the Up status indicator within the Network dashlet.

Answer: B

NEW QUESTION 17
Which three tasks must be completed in preparation of a site for an ACP 4200 installation? (Choose three.)

• A. Determine the list of Customer Administrators who will require login access to the ACP 4200.
• B. Install power connections for the ACP 4200.
• C. Plan the path from the delivery location to the permanent site.
• D. Determine a permanent location for the ACP 4200.
• E. Enable SNMP management on the network devices that will be connected to the ACP 4200.

Answer: ABC

NEW QUESTION 18
......