Q1. An engineer installed a 3702 AP and is getting power from the switch. What is the reason for getting 3x3 MIMO instead of 4x4?

A. 802.1p 

B. 802.3af 

C. 802.11e 

D. 802.3at

View Answer

Q2. Which two options describe best practices that must be completed after a wireless installation is finished?

(Choose two.)

A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.

B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.

C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.

D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.

E. Test all the customer’s wireless devices and applications to ensure they are working properly.

View Answer

Q3. A customer wants to implement a wireless network in a historic location, but is concerned about the structural and aesthetic impact to the facility. Which benefit of using wireless mesh addresses these concerns?

A. Power is required only at the installation location.

B. The APs do not have LED lights.

C. More wireless channels can be supported.

D. APs do not need network connections.

View Answer

Q4. A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

A. Deploy the specified access points per area type.

B. Resurvey and adjust the design.

C. Increase the Tx power on incorrectly surveyed access points.

D. Deploy unsurveyed access points to the design.

View Answer

Q5. A customer has a business-critical voice network and wants to be alerted whenever voice clients move out of a coverage area and experience RSSI below -67 dBm on the 5 GHz band. Which option can be configured on the wireless controller to alert network administrators when this limit is surpassed?

A. EDCA; voice optimized

B. SIP voice sample interval

C. 802.11a voice RSSI coverage threshold

D. traffic stream metrics

View Answer

Q6. An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

A. external connector access point

B. integrated antenna access point

C. coax low-loss cable

D. battery operated power supply

E. range finder

F. Yagi antennas

View Answer

Q7. An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?

A. Deploy access points where the survey indicates and connect them via fiber optic cable, using a mediaadapter, and locally provide power.

B. Deploy access points to each phone location converting two spare pairs of copper from the phone line toEthernet and locally provide power.

C. Deploy access point devices where limited cable can be run or exists and connect high- gain antennas andincrease Tx power to increase cell size.

D. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.

View Answer

Q8. Refer to the exhibit.

While testing the post-deployment WLAN network, you discover that an AP has been placed in a difficult area.

The AP cannot be moved easily because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.)

A. Add additional APs.

B. Increase the AP power level to maximum.

C. Rotate the AP 90 degrees to change antenna polarity.

D. Replace the AP with an AP and external antenna.

E. Change the AP location to one that is less RF hostile.

View Answer

Q9. An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?

A. overlapping -72 dBm coverage from two access points

B. overlapping -67 dBm coverage from two access points

C. continuous -67 dBm coverage from one access point

D. continuous -72 dBm coverage from one access point

View Answer

Q10. An engineer is preparing for an active site survey of a warehouse and is informed that they should not enter any areas that are blocked by supplies that are difficult to move. Which option describes how the engineer should address this restriction?

A. Extrapolate restricted access areas by drawing circles for AP coverage

B. Survey hallways, common areas, and storerooms.

C. Utilize a predictive tool to define coverage in off-limits areas.

D. Educate the customer about the importance of accurate and complete measurements.

View Answer