Question No: 5

The Ajax Corporation is designing an IP telephony network using Cisco MCS 7845 Series servers, each one capable of supporting 7500 devices. The design must meet these requirements:

-Be cost-effective

-Support up to 7500 phones

-Provide a minimal level of redundancy

A. Two Cisco Unified Communications Manager servers:1 publisher and TFTP server combined.1 primary subscriber.

B. Three Cisco Unified Communications Manager servers:1 publisher and TFTP server combined.1 primary subscriber.1 backup subscriber.

C. Four Cisco Unified Communications Manager servers:1 publisher.1 TFTP server.1 primary subscriber.1 backup subscriber.

D. Five Cisco Unified Communications Manager servers:1 publisher.1 TFTP server.1 primary subscriber.2 backup subscribers.

View Answer

Question No: 6

Time-of-day routing in Cisco Unified Communications Manager is configured in which of these ways?

A. by specifying a time schedule on the phone device CSS

B. by specifying a time period on the phone device CSS

C. by specifying a time schedule on the partition that is being used for time-of-day routing

D. by specifying a time period on the partition that is being used for time-of-day routing

E. directly on the route pattern using an explicit timetable

View Answer

Question No: 7

What is the default option for framing when you configure T1 controller?

A. Super Frame

B. alternate mark inversion

C. C.Extended Super Frame

D. D.cyclic redundancy check 4

E. E.high-density bipolar 3

F. F.No-CRC4

G. G.binary 8-zero substitution

H. Australia

View Answer

Question No: 8

Refer to the exhibit.

What is the command to place the static IP address by CLI in the Cisco TelePresence MSE 8000?

A. MSE 8050: static 0 10.10.2.13 255.255.255.255 10.10.2.1 200.87.100.10 200.87.100.20.

B. MSE 8050: static 0 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.

C. MSE 8050: static 1 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.

D. MSE 8050: static ip 0 10.10.2.13 255.255.255.0 10.10.2.1 200.87.100.10 200.87.100.20.

View Answer

Question No: 9

Which three Cisco Unified Communications Manager settings can be used to support IP

phone services? (Choose three.)

A. Device Defaults

B. Enterprise Parameters

C. IP Phone Service Configuration window

D. Common Phone Profile

E. Service Parameters

F. Phone Configuration window

View Answer

Question No: 10

Refer to the exhibit.

An engineer is trying to determine the status of the ISDN D Channel on a new PRI circuit, types in the show isdn status command, and sees this output. Which two pieces of information can be determined from this output? (Choose two.)

A. The provider is using the 5ESS protocol.

B. There are four channels.

C. The connection to the Cisco Unified Communications Manager has been established.

D. The D channel is working correctly.

E. No active calls are established.

View Answer

Question No: 11

Which tool can you use to verify and troubleshoot a dial plan?

A. Audit Log Configuration

B. Dialed Number Analyzer

C. CDR Analysis and Reporting

D. Troubleshooting Trace Settings

View Answer

Question No: 12

You are a Voice Engineer at ABC Company. You want to provision a new voice gateway for a remote site, and you need to configure 24 channels of a T1 CAS interface. Which set is the correct set of commands for this configuration?

A. R1(config)# controller t1 1/0R1(config-controller)# framing esfR1(config-controller)# linecode b8zsR1(config-controller)# primary-group 1 timeslot 1-24 type fxo-loop-start

B. R1(config)# controller t1 1/0R1(config-controller)# linecode hdb3R1(config-controller)# framing crc4R1(config-controller)# clock source lineR1(config-controller)# ds0-group 1 timeslot 1-24 type fxo-loop-start

C. R1(config)# isdn switch-type primary-5essR1(config)# controller t1 t1/0R1(config-

controller)# pri-group timeslots 1-24

D. R1(config)# controller t1 1/0R1(config-controller)# framing esfR1(config-controller)# linecode b8zsR1(config-controller)# clock source lineR1(config-controller)# ds0-group 1 timeslot 1-24 type fxo-loop-start

View Answer

Question No: 13

A voice engineer is troubleshooting an issue that involves incoming calls to POTS lines. Which command verifies the digits that are received by voice-port?

A. debug voip dial-per

B. debug vtsp session

C. debug vtsp dsp

D. debug call treatment

E. debug voice protocol

View Answer

Question No: 14

Which distribution algorithm is used for a route group?

A. Circular, top down.

B. Longest idle, broadcast.

C. Circular, top down, longest idle, broadcast.

D. Top down, broadcast, circular.

View Answer