Q1. A technician is connecting a NAS device to an Ethernet network. Which of the following technologies will be used to encapsulate the frames? 

A. HTTPS 

B. Fibre channel 

C. iSCSI 

D. MS-CHAP 

View Answer

Q2. A technician is installing a surveillance system for a home network. The technician is unsure which ports need to be opened to allow remote access to the system. Which of the following should the technician perform? 

A. Disable the network based firewall 

B. Implicit deny all traffic on network 

C. Configure a VLAN on Layer 2 switch 

D. Add the system to the DMZ 

View Answer

Q3. Which of the following network topologies has a central, single point of failure? 

A. Ring 

B. Star 

C. Hybrid 

D. Mesh 

View Answer

Q4. A company wants to create highly available datacenters. Which of the following will allow the company to continue to maintain an Internet presence at all sites in the event that a WAN circuit at one site goes down? 

A. Load balancer 

B. VRRP 

C. OSPF 

D. BGP 

View Answer

Q5. Which of the following does a network technician need to implement if a change is unsuccessful within the approved maintenance window? 

A. Configuration procedures 

B. Stakeholder notification 

C. Impact analysis 

D. Rollback procedure 

View Answer

Q6. A system administrator has been tasked to ensure that the software team is not affecting the production software when developing enhancements. The software that is being updated is on a very short SDLC and enhancements must be developed rapidly. These enhancements must be approved before being deployed. Which of the following will mitigate production outages before the enhancements are deployed? 

A. Implement an environment to test the enhancements. 

B. Implement ACLs that only allow management access to the enhancements. 

C. Deploy an IPS on the production network. 

D. Move the software team's workstations to the DMZ. 

View Answer

Q7. A network technician is utilizing a network protocol analyzer to troubleshoot issues that a user has been experiencing when uploading work to the internal FTP server. Which of the following default port numbers should the technician set the analyzer to highlight when creating a report? (Select TWO). 

A. 20 

B. 21 

C. 22 

D. 23 

E. 67 

F. 68 

G. 69 

View Answer

Q8. The administrator's network has OSPF for the internal routing protocol. One port going out to the Internet is congested. The data is going out to the Internet, but queues up before sending. Which of the following would resolve this issue? 

Output: 

Fast Ethernet 0 is up, line protocol is up 

Int ip address is 10.20.130.5/25 

MTU 1500 bytes, BW10000 kbit, DLY 100 usec 

Reliability 255/255, Tx load 1/255, Rx load 1/255 

Encapsulation ospf, loopback not set Keep alive 10 

Half duplex, 100Mb/s, 100 Base Tx/Fx 

Received 1052993 broadcasts 

0 input errors 

983881 packets output, 768588 bytes 

0 output errors, 0 collisions, 0 resets 

A. Set the loopback address 

B. Change the IP address 

C. Change the slash notation 

D. Change duplex to full 

View Answer

Q9. A network administrator has created a virtual machine in the cloud. The technician would like to connect to the server remotely using RDP. Which of the following default ports needs to be opened? 

A. 445 

B. 3389 

C. 5004 

D. 5060 

View Answer

Q10. Which of the following refers to a network that spans several buildings that are within walking distance of each other? 

A. CAN 

B. WAN 

C. PAN 

D. MAN 

View Answer