NEW QUESTION 1
You are troubleshooting a newly installed desktop Oracle Solaris 11 system with a single network interface. From this system, you can connect to other systems within the company
intranet, but cannot access any external services (such as websites and email), even when using IP addresses.
Examining the routing table confirms that the default route to 192.168.1.1 is missing. DHCP is not used at this site. Which two commands will temporarily mid permanently configure the default route?

• A. ipadm set-gateway 192.168.1.1
• B. route add default 192.168.1.1
• C. ipadm set-default 192.168.1.1
• D. dladm route-add –d 192.168.1.1
• E. echo 192.168.1.1 >/etc/gateway
• F. echo 192.168.1.1 >/etc/defaultrouter

Answer: BF

Explanation: B: Setting the default route on Solaris is easy. If you are trying to just set the route temporarily you can use the route command:
Route add default <ipaddress> Example:
Route add default 192.168.1.1
Note: Route command manipulates the kernel routing tables. Routing is the process of forwarding a packet from one computer to another. It is based on the IP address in the IP packet header and netmask.
F: If you want the route to be persisted when you reboot the system, you will need to set the route in the /etc/defaultrouter file.
/etc/defaultrouter Example:
Echo 192.168.1.1 > /etc/defaultrouter

NEW QUESTION 2
To confirm the IP addresses and netmasks have been correctly configured on the network interfaces, which command(s) should you use?

• A. ipadm show-if
• B. ipadm show-nic
• C. ipadm show-addr
• D. ipadm show-addripadm show-mask
• E. ipadm show-ipipadm show-mask
• F. ipadm show-config

Answer: C

Explanation: Show address information, either for the given addrobj or all the address objects configured on the specified interface, including the address objects that are only in the persistent configuration.
Example:
# ipadm show-addr
ADDROBJ TYPE STATE ADDR
lo0/v4 static ok 127.0.0.1/8 lo0/v6 static ok ::1/128

NEW QUESTION 3
You are going to create live zones on you server. Disk space is critical on this server so you need to reduce the amount of disk space required for these zones. Much of the data required for each of these zones is identical, so you want to eliminate the duplicate copies of data and store only data that is unique to each zone.
Which two options provide a solution for eliminating the duplicate copies of data that is common between all of these zones?

• A. Create the zones by using sparse root zones.
• B. Set the dedup property to on and the dedupratio to at least 1.5 for the zpool.Create a separate ZFS file system for each zone in the zpool.
• C. Put all of the zones in the same ZFS file system and set the dedupratio property for the ZFS file system to at least 1.5.
• D. Put all of the zones in the same ZFS file system and set the dedup property for the file system to on.
• E. Put each zone in a separate ZFS file system within the same zpoo
• F. Set the dedup property to on for each ZFS file system.

Answer: DE

Explanation: n Oracle Solaris 11, you can use the deduplication (dedup) property to remove redundant data from your ZFS file systems. If a file system has the dedup property enabled, duplicate data blocks are removed synchronously. The result is that only unique data is stored, and common components are shared between files.

NEW QUESTION 4
What is the result of executing the following command? svcs -d svc:/network/ssh:default

• A. disables the svc:/network/ssh:default service
• B. displays the services that svc: /network/ssh:default is dependent on
• C. displays the services that are dependent on the svc: /network/ssh:default service
• D. deletes the svc: /network/ssh:default service

Answer: B

Explanation: The svcs command displays information about service instances as recorded in the service configuration repository.
-d Lists the services or service instances upon which the given service instances depend.

NEW QUESTION 5
You want to display the IP address assignments of the network interfaces. Which command should you use?

• A. ipadm show-if
• B. ipadm show-addr
• C. ipadm show-prop
• D. ipadm show-addrprop

Answer: B

Explanation: 'ipadm show-addr' displays all the configured addresses on the system. Example:
# ipadm show-addr
ADDROBJ TYPE STATE ADDR
lo0/v4 static ok 127.0.0.1/8 lo0/v6 static ok ::1/128

NEW QUESTION 6
You have Solaris 11 system with a host name of sysA and it uses LDAP as a naming service.
You have created a flash archive of sysA and you want to migrate this system to an Oracle Solaris11 server, Solaris10 branded zone.
The zone Status on the Oracle Solaris 11 server is:
- zone10 incomplete/zone/zone1solaris10exc1
Select the option that will force the non-global zone to prompt you for a host name and name service the first time it is booted.

• A. Use zonecfg to change the zonename before booting the system for the first time
• B. Use the - u option with the zoneadm - z zone10 attach command.
• C. Use the -u option with the zoneadn -z zone10 install command.
• D. Remove the sysidcfg file from the <zonepath>/root directory before booting the non- global zone.

Answer: C

Explanation: Oracle Solaris 10 branded zones – Oracle Solaris 10 Zones provide an Oracle Solaris 10
environment on Oracle Solaris 11. You can migrate an Oracle Solaris 10 system or zone to a solaris10 zone on an Oracle Solaris 11 system in the following ways:
* Create a zone archive and use the archive to create an s10zone on the Oracle Solaris 11 system.
This option applies in the current scenario.
Example of command to Install the Oracle Solaris 10 non-global zone. s11sysB# zoneadm -z s10zone install -u -a /pond/s10archive/s10.flar
* Detach the zone from the Oracle Solaris 10 system and attach the zone on the Oracle Solaris 11 zone. The zone is halted and detached from its current host. The zonepath is moved to the target host, where it is attached.
Note:
install [-x nodataset] [brand-specific options] A subcommand of the zoneadm.
Install the specified zone on the system. This subcommand automatically attempts to verify first. It refuses to install if the verify step fails.
-u uuid-match
Unique identifier for a zone, as assigned by libuuid(3LIB). If this option is present and the argument is a non-empty string, then the zone matching the UUID is selected instead of the one named by the -z option, if such a zone is present.

NEW QUESTION 7
Your server has a ZFS storage pool that is configured as follows:

The following partition scheme is used for every disk drive in pool1:

Which two are true regarding the ZFS storage pool?

• A. The data on c3t3d0 is duplicated on c3t4do.
• B. The data is striped across disks c3t3d0 and c3t4do and mirrored across vdevs mirror-0 and mirror-1.
• C. The storage pool is 146 GB total size (rounded to the nearest GB).
• D. The storage pool is 584 G8 total size (rounded to the nearest GB).
• E. The storage pool is 292 GB total size (rounded to the nearest GB).

Answer: AE

NEW QUESTION 8
In Oracle Solaris 11, where is the Oracle default repository located?

• A. /var/spool/pkg
• B. http://localhost/solaris
• C. http://pkg.oracle.com/solaris/release
• D. http://www.oracle.com/Solaris/download
• E. /cdrom/cdrom0

Answer: C

Explanation: REPOSITORY DESCRIPTION
* http://pkg.oracle.com/solaris/release
The default repository for new Oracle Solaris 11 users. This repository receives updates for each new release of Oracle Solaris. Significant bug fixes, security updates, and new software may be provided at any time for users to install at Oracle's discretion.
*https://pkg.oracle.com/solaris/support
Provides bug fixes and updates. Accessible with a current support contract from Oracle.
* https://pkg.oracle.com/solaris/dev Provides the latest development updates. Accessible to users enrolled in the Oracle Solaris 11 Platinum Customer Program and approved Oracle Partners.

NEW QUESTION 9
You are troubleshooting the Oracle Solaris11 Automated Installer (AI), which is not connecting with the IPS software repository.
Which three steps will help determine the cause of DNS name resolution failure?

• A. Verify the contents of /etc/resolve.conf.
• B. Run netstat -nr to verify the routing to the DNS server.
• C. Ping the IP address of the IPS server to verify connectivity.
• D. On the installation server, verify that the menu.1st file for the client points to a valid boot arc hive.
• E. Run df -k to verify that the boot directory containing the boot archive is loopback mounted under /etc/netboot.
• F. Run the command /sbin/dhcpinfo DNSserv to ensure that the DHCP server providing the DNS server information.

Answer: ABF

Explanation: Check DNS
* (A) Check whether DNS is configured on your client by verifying that a non-empty
/etc/resolv.conf file exists.
* (F) If /etc/resolv.conf does not exist or is empty, check that your DHCP server is providing DNS server information to the client:
# /sbin/dhcpinfo DNSserv
If this command returns nothing, the DHCP server is not set up to provide DNS server information to the client. Contact your DHCP administrator to correct this problem.
* (B) If an /etc/resolv.conf file exists and is properly configured, check for the following possible problems and contact your system administrator for resolution:
** The DNS server might not be resolving your IPS repository server name.
** No default route to reach the DNS server exists.

NEW QUESTION 10
To assist in examining and debugging running processes, Solaris 11 has a utility that returns pro arguments and the names and values of environment variables.
What is the name of this utility?

• A. ppgsz
• B. pargs
• C. pmap
• D. pgrep

Answer: B

Explanation: The pargs utility examines a target process or process core file and prints arguments, environment variables and values, or the process auxiliary vector.

NEW QUESTION 11
Given:
file1 and file2 are text files. dir1 and dir2 are directories.
Which two commands will be successful?

• A. cp dir1 dir1
• B. cp dir1 file1
• C. cp file? dir1
• D. cp fil
• E. dir1
• F. cp file% dir2
• G. cp file1 file2 dir1

Answer: CF

Explanation: C: Here the wildcard character ? is used (Matches any single character). file1 and file2 will be copied into dir1
F: the two files file1 and file2 are copied into directoy dir1. Note: cp - copy files and directories
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY.
Cp has three principal modes of operation. These modes are inferred from the type and count of arguments presented to the program upon invocation.
* When the program has two arguments of path names to files, the program copies the contents of the first file to the second file, creating the second file if necessary.
* When the program has one or more arguments of path names of files and following those an argument of a path to a directory, then the program copies each source file to the destination directory, creating any files not already existing.
* When the program's arguments are the path names to two directories, cp copies all files in the source directory to the destination directory, creating any files or directories needed. This mode of operation requires an additional option flag, typically r, to indicate the
recursive copying of directories. If the destination directory already exists, the source is copied into the destination, while a new directory is created if the destination does not exist.

NEW QUESTION 12
Review the storage pool information:

Which statement describes the status of this storage pool?

• A. It is a RAIDZ storage pool and can withstand a single disk failure; data will be striped at: disk components.
• B. It is a double-parity RAIDZ storage pool and can withstand two disk failures; data will be striped across four disk components.
• C. It is an improperly configured RAIDZ storage pool; data will be striped across four disk components, but only three drives are protected with redundancy.
• D. It is an improperly configured RAIDZ storage pool; data will be striped across three disk components, but only three drives are protected with redundancy.

Answer: D

Explanation: Device c3t6d0 is not included in the RAIDZ storage pool. The other three devices are included in the raidz pool. The data on these devices are protected.
Note: In addition to a mirrored storage pool configuration, ZFS provides a RAID-Z configuration with either single, double, or triple parity fault tolerance. Single-parity RAID-Z (raidz or raidz1) is similar to RAID-5. Double-parity RAID-Z (raidz2) is similar to RAID-6.

NEW QUESTION 13
The /usr/bin/p7zip file that is part of the p7zip package has been overwritten. This server is critical to production and cannot be rebooted. Identify the command that would restore the file without requiring a reboot.

• A. pkg verify p7zip
• B. pkg fix p7sip
• C. pkg rebuild-index p7zip
• D. pkg revert p7zip
• E. pkg uninstsll p7zip
• F. pkg install p7zip
• G. pkg install --no-backup-be p7sip
• H. pkg refresh p7zip

Answer: D

Explanation: Use the pkg revert command to restore files to their as-delivered condition.

NEW QUESTION 14
You have a user that needs to use the cron tool to schedule some repetitive tasks. When the user enters the crontab –e command in a terminal window, the following error appears:
crontab: you are not authorized to use cron. Sorry
In order to troubleshoot this issue, in what directory would you start your invest

• A. /etc/cron.d
• B. /var/spool/cron
• C. /var/spool/cron/crontable
• D. /var/spool/cron/atjobs

Answer: A

Explanation: crontab: you are not authorized to use cron. Sorry.
This message means that either the user is not listed in the cron.allow file (if the file exists), or the user is listed in the cron.deny file.
You can control access to the crontab command by using two files in the /etc/cron.d directory: cron.deny and cron.allow. These files permit only specified users to perform crontab command tasks such as creating, editing, displaying, or removing their own crontab files.
The cron.deny and cron.allow files consist of a list of user names, one user name per line.

NEW QUESTION 15
Which two statements are true concerning the network stack on Oracle Solaris 11?

• A. Hardware network interfaces and datalinks have a one-to-one relationship.
• B. IP addresses are assigned to datalinks.
• C. A single IP interface can have either an IPv4 address or an IPv6 address but not both.
• D. A single IP interface can have both an IPv4 address and an IPv6 address.
• E. A single datalink can have only one IP interface.

Answer: AD

NEW QUESTION 16
You are installing Oracle Solaris 11 on a SPARC-based system by using the Test Installer. Which three statements are true?

• A. The ROOT user will always be configured as a role.
• B. The root filesystem will always be deployed on ZFS.
• C. The root filesystem will always be located on a local disk.
• D. The network can be configured using DHCP.
• E. The set of packages that will be installed are server based.
• F. You must always create one regular user when installing the system.

Answer: BDE