NEW QUESTION 1
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?

• A. show telemetry pipeline stats
• B. show telemetry transport
• C. show telemetry control stats
• D. show analytics system-load

Answer: B

NEW QUESTION 2
Refer to the exhibits.


A storage network engineer activates a zoneset on MDS-A and verifies the successful activation (Exhibit 1). The engineer is then notified that there is a SAN outage (Exhibit 2) What is the cause of the outage?

• A. Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
• B. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.
• C. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric.
• D. Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric.

Answer: D

NEW QUESTION 3
DRAG DROP
Drag and drop the items from the left onto the correct descriptions on the right. Not all items are used.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 4
Which result occurs when a VSAN is deleted that contains non-trunking ports?

• A. The ports are moved to VSAN 4094.
• B. The ports are moved to VSAN 1.
• C. The ports are removed from the configuration.
• D. The port configurations are cleared.

Answer: A

NEW QUESTION 5
A storage administrator is configuring inter-VSAN routing on a fabric that contains duplicate domain IDs. Which feature must be configured to ensure continued operation?

• A. auto topology
• B. transit VSANs
• C. IVR NAT
• D. virtual domains

Answer: C

NEW QUESTION 6
Which two protocols are used to implement SAN telemetry on Cisco MDS switches? (Choose two.)

• A. RPC transport
• B. GPB transport
• C. gRPC transport
• D. gRPC encoding
• E. GPB encoding

Answer: CE

NEW QUESTION 7
What is the effect of a non-graceful virtual machine shutdown on a virtualized server that is connected to a SAN with Fibre Channel interfaces?

• A. NP Port reload connected to the upstream SAN switch
• B. out-of-service Fibre Channel interfaces on the SAN switch
• C. frames stuck in the storage system
• D. frames stuck in the HBA buffer of the server

Answer: B

NEW QUESTION 8
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules. The install command is executed on the standby supervisor module but fails. Which action would have prevented this failure?

• A. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
• B. The upgrade must be done on the active supervisor module only.
• C. Cisco Fabric Services must be disabled before starting the upgrade.
• D. Fabric Controller Service must be stopped before starting the upgrade.

Answer: B

NEW QUESTION 9
A storage network engineer is implementing a port channel for multiple FCIP interfaces with write acceleration in a client’s storage network. Which channel mode must be used?

• A. on
• B. passive
• C. active
• D. force

Answer: C

NEW QUESTION 10
A network engineer is configuring a Cisco MDS switch for FCoE. Which two conditions must be considered during the implementation phase? (Choose two.)

• A. On Cisco MDS switches, system-defined class maps for class-FCoE and class-default are enabled but can be deleted.
• B. The QoS policy must be identical to other Cisco FCoE switches in the network.
• C. On the Cisco MDS, the MTU is set equal to 2112.
• D. VLAN 1 or the native VLAN can be mapped to an FCoE VSAN.
• E. FCoE is already enabled on a Cisco MDS switch.

Answer: BE

NEW QUESTION 11
Which configuration is available only in Cisco DCNM-SAN Advanced mode?

• A. IVR
• B. VMpath configuration
• C. zoning
• D. template-based provisioning

Answer: A

NEW QUESTION 12
What is the function of the 0xFFFFFC address in a Fibre Channel fabric?

• A. management server
• B. fabric controller
• C. name server
• D. time server

Answer: C

NEW QUESTION 13
Refer to the exhibit.

What is the result of merging the fabric?

• A. The merged fabric IVR VSAN topology is set to activate.
• B. The merged fabric has NAT enabled.
• C. The merge is invalid.
• D. The merged fabric contains only service group Group1.

Answer: D

NEW QUESTION 14
DRAG DROP
Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 15
Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?

• A. administrator password
• B. management IP address
• C. active NTP server
• D. active default gateway

Answer: A

NEW QUESTION 16
Which action must be performed to deactivate a VSAN without losing its configuration?

• A. Isolate it.
• B. Delete it.
• C. Rename it.
• D. Suspend it.

Answer: D

NEW QUESTION 17
A storage administrator wants to enable NPV in a Fibre Channel edge switch. Which configuration is supported in this mode?

• A. Cisco Fabric Services distribution over Fibre Channel
• B. E Port connectivity to the core switch
• C. local switching of east-west traffic
• D. Dynamic Port VSAN Membership

Answer: A

NEW QUESTION 18
Which Cisco NX-OS command displays the VSAN that is associated with each FCID?

• A. show fcdomain
• B. show fc2 plogi
• C. show vsan database
• D. show flogi database

Answer: A

NEW QUESTION 19
Refer to the exhibit.

Which command is used to determine which switch has the lock?

• A. show zoneset active
• B. show zone status
• C. show flogi database

Answer: C

NEW QUESTION 20
The principal switch on a Fibre Channel network fails to assign requested domain to a subordinate switch. What are two reasons? (Choose two.)

• A. Cisco Fabric Services distribution is not enabled on the switch.
• B. The fabric is locked.
• C. The requested domain is outside the allowed list.
• D. The persistent FC ID feature is not enabled.
• E. An existing switch already has the requested domain assigned.

Answer: CE

NEW QUESTION 21
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

• A. MDS(config)# interface fc 1/1MDS(config-if)# fcsp esp manual
• B. MDS(config)# fcsp esp manual
• C. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp mode gcm MDS(config-if-fcsp)# fcsp esp manual
• D. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual MDS(config-if-fcsp)# mode gcm

Answer: A

NEW QUESTION 22
Which component is initially responsible for loading the kickstart image on Cisco MDS Switches?

• A. ROMMON
• B. BIOS
• C. NX-OS
• D. BASH

Answer: C

NEW QUESTION 23
......