Q16. Refer to the exhibit.

When packets are transmitted from R1 to R2, where are they encrypted?

A. On the E0/1 interface on R2

B. On the outside Interface

C. In the tunnel

D. In the forwarding engine

E. Within the crypto map

F. On the E0/0 interface on R1

View Answer

Q17. Which statement about Type-4 LSA in OSPFv2 is true?

A. It is present only in the backbone area

B. It is generated by each ABR and forwarded in non-stub areas.

C. It is forwarded in NSSA areas.

D. It is generated by the ASBR and forwarded throughout the wholeOSPF domain.

View Answer

Q18. router bgp 65500

neighbor LocalSite ebgp-multihop 2

neighbor LocalSite update-source Loopback0 neighbor LocalSite next-hop-self

neighbor LocalSite route-map CheckCommunity in neighbor LocalSite route-map CPodPeer out

route-map CPodPeer permit 10 match as-path 1

route-map CPodPeer permit 20 match as-path 33

route-map CPodPeer deny 30

ip as-path access-list 1 permit ^$

ip as-path access-list 33 permit _65006$

Refer to the exhibit. Considering a stable neighborship has been established with multiple eBGP peers, which routers are advertised by the router?

A. Only BGP routes sourced on this router

B. Only BGP routes from AS 65006

C. BGP routes that passed through AS 65006 and BGP routes sourced on this router

D. All routes

View Answer

Q19. R1#showip ospfinterface FastEthernet0/0.12

...Network Type

Non_BROADCAST...

...

R2#showip ospfinterface FastEthernet0/0.12

...Network Type BROADCAST...

...

Refer to the exhibit. OSPF is configured on R1 and R2 as shown. which action can you take to allow a

neighbor relationship to be established.

A. On R1, change the process ID to 1

B. On R1, set the network type of the FastEthernet0/0.12 interface to broadcast

C. Configure R1 and R2 as neighbors using interface addresses

D. Configure R1 and R2 as neighbors using router IDs

View Answer

Q20. What are two differences between IPv6 ISATAP tunneling and IPv6 6to4 tunneling? (Choose two)

A. Only ISATAP tunneling transfers unicast IPv6 packets between .sites.

B. Only 6to4 tunneling requires 2002::/16 addresses. -

C. Only ISATAP tunneling can transfer IPv6 multicast packets.

D. Only ISATAP tunneling transfers unicast IPv6 packets within a site

E. Only 6to4 tunneling transfers unicast IPv6 packets within a site.

View Answer

Q21. R1

interface Loopback0

ip address 172.16.1.1 255.255.255.255

interface FastEthernet0/0

ip address 192.168.12.1 255.255.255.0

router eigrp 100 no auto-summary

redistribute connected metric 10000 1 255 1 1500 router ospf1

redistribute eigrp 100

network 192.168.12.0 0.0.0.255 area 0 R2

interface FastEthernet0/0

ip address 192.168.12.2 255.255.255.0

router ospf1

network 192.168.12.0 0.0.0.255 area 0

Refer to the exhibit. While troubleshooting a connectivity issue between R1 and R2, you determine that R1's

Loopback0 network is missing from R2's route table. What is this likely cause the problem>

A. The router is configured to redistribute only broadcast networks

B. The router can redistribute only point-to-point networks

C. The route is excluding the Loopback0 interface fro redistribute because it si redistributing other OSPF

interface

D. The subnets keywords is missing from the redistribute eigrp command on R1

View Answer

Q22. Which command can you enter to disable logging for VTY lines?

A. No logging monitor

B. No logging buffer

C. No logging console

D. No logging trap

E. No logging count

View Answer