Question No: 10

ON NO: 402

Refer to the exhibit.

Which two statements about the output are true? (Choose two.)

A. 802.1D spanning tree is being used.

B. Setting the priority of this switch to 0 for VLAN 1 would cause it to become the new root.

C. The hello, max-age, and forward delay timers are not set to their default values.

D. Spanning-tree PortFast is enabled on GigabitEthernet1/1.

View Answer

Question No: 11

Which option describes how the IP address is assigned when you configure a Layer 3 EtherChannel interface?

A. You must assign the IP address to the tunnel interface.

B. The last IP address added to the EtherChannel is used automatically.

C. You must assign the IP address to a port channel logical interface.

D. The first IP address added to the EtherChannel is used automatically.

View Answer

Question No: 12

Refer to the exhibit.

Which three statements about the R1 configuration are true? (choose three.

A. The virtual circuit identifier is 4006 and the virtual circuit is down.

B. This circuit is using MPLS VC type 4.

C. The local label for the circuit is 1611.

D. The virtual circuit identifier is 1611 and the virtual circuit is down.

E. The targeted LDP session to the remote peer is up.

F. The local label for the circuit is 4006.

View Answer

Question No: 13

Refer to the exhibit.

Which additional configuration statement is required on R3 in order to allow multicast traffic sourced from 192.168.13.3 to flow along the shared-tree?

A. ip route 192.168.14.0 255.255.255.0 Tunnel 0

B. ip route 10.4.4.4 255.255255.255 Tunnel 0

C. ip mroute 10.4.4.4 255.255.255.255 Tunnel 0

D. ip mroute 192.168.14.0 255.255.255.0 Tunnel 0

View Answer

Question No: 14

Refer to the exhibit After you configure the given IP SLA on a Cisco router.you note that the device is unable to fialover to the backup route even when pings to 10.12.34.5 fail.What action can you take to correct the problem?

A. Change the ip route 0.0.0.0.0.0.0.0.192.168.1.1.53.200 command to ip route 0.0.0.0.0.0.0.0 192.168.1.153.12.

B. Change the ip sla schedule 12 life forever start-time now comman to ip sla schedule 12 life forever start-time 00:12 00

C. Change the track 12 ip sla 12 state command to track 12 ip sla 12 reachability.

D. Change the frequency 2 command to frequency 12.

View Answer

Question No: 15

Which two items must be confined to caputure packet data with the Embedded Packet Caputure feature ? (Choose two)

A. the capture point

B. the capture buffer

C. the coputure file export location

D. the caputure filter

E. the capture rate

F. the buffer memory size

View Answer

Question No: 16

Which three modes are valid for forming an EtherChannel between the ports of two switches? {Choose threE.

A. passive/passive

B. active/active

C. active/passive

D. desirable/on

E. auto/auto

F. auto/desirable

View Answer

Question No: 17

Which keychain cryptographic algorithm is supported by the IS-IS routing protocol?

A. MD5

B. HMAC-SHA1-12

C. HMAC-SHA1-20

D. HMAC-MD5

View Answer

Question No: 18

Where must the spanning-tree timers be configured if they are not using the default timers?

A. Changing the default timers is not allowed

B. They must be on any non-root bridge

C. Timers must be modified manually in each switch

D. They must be on the root bridge

View Answer

Question No: 19

Which three technologies can be used to implement redundancy for IPv6? (choose three.

A. IPv6 NA

B. NHRP

C. HSRP

D. DVMRP

E. GLBP

F. IPv6 RA

View Answer