Answer: A,E 

Answer: B,C 

Explanation: 

The EIGRP Over the Top feature enables a single end-to-end Enhanced Interior Gateway Routing Protocol (EIGRP) routing domain that is transparent to the underlying public or private WAN transport that is used for connecting disparate EIGRP customer sites. When an enterprise extends its connectivity across multiple sites through a private or a public WAN connection, the service provider mandates that the enterprise use an additional routing protocol, typically the Border Gateway Protocol (BGP), over the WAN links to ensure end-to-end routing. The use of an additional protocol causes additional complexities for the enterprise, such as additional routing processes and sustained interaction between EIGRP and the routing protocol to ensure connectivity, for the enterprise. With the EIGRP Over the Top feature, routing is consolidated into a single protocol (EIGRP) across the WAN. 

Perform this task to configure a customer edge (CE) device in a network to function as an EIGRP Route Reflector: 

1. enable 

2. configure terminal 

3. router eigrp virtual-name 

4. address-family ipv4 unicast autonomous-system as-number 

5. af-interface interface-type interface-number 

6. no next-hop-self 

7. no split-horizon 

8. exit 

9. remote-neighbors source interface-type interface-number unicast-listen lisp-encap 

10. network ip-address 

11. end 

Note. Use no next-hop-self to instruct EIGRP to use the received next hop and not the local outbound interface address as the next hop to be advertised to neighboring devices. If no next-hop-self is not configured, the data traffic will flow through the EIGRP Route Reflector. 

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/ire-xe-3s-book/ire-eigrp-over-the-top.html 

Answer:  

Answer: A 

Explanation: 

The switch with the highest switch priority (the lowest numerical priority value) is elected as the root switch. If all switches are configured with the default priority (32768), the switch with the lowest MAC address in the VLAN becomes the root switch. 

Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_53_se/configuration/guide/2960scg/swstp.html 

Answer: C 

Answer: A 

Explanation: 

Only option A specified that the exceed and violate actions are set to drop for traffic over the CIR of 6 Mbps, and is also configured to set all traffic with a COS of 1 using the “set cos1” command. 

Answer: A,B 

Explanation: 

Packets exchanged between neighbors must be authenticated to ensure that a device accepts packets only from devices that have the same preshared authentication key. Enhanced Interior Gateway Routing Protocol (EIGRP) authentication is configurable on a per-interface basis; this means that packets exchanged between neighbors connected through an interface are authenticated. EIGRP supports message digest algorithm 5 (MD5) authentication to prevent the introduction of unauthorized information from unapproved sources. MD5 authentication is defined in RFC 1321. EIGRP also supports the Hashed Message Authentication Code-Secure Hash Algorithm-256 (HMAC-SHA-256) authentication method. 

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/ire-xe-3s-book/ire-sha-256.html 

Answer: A 

Explanation: 

In some situations, you can prevent a PC connected to the Cisco IP Phone from taking advantage of a high-priority data queue. You can use the switchport priority extend cos interface configuration command to configure the telephone through the switch CLI to override the priority of the traffic received from the PC. 

Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2950/software/release/12-1_22_ea2/configuration/guide/2950scg/swqos.html 

Answer: C,F 

Explanation: 

To allow the use of external, internal, and local administrative distances that could be a better route than other external, internal, or local routes to a node, use the distance bgp command in address family or router configuration mode. To return to the default values, use the no form of this command. distance bgp external-distance internal-distance local-distance no distance bgp 

. Syntax Description 

external-distance 

Administrative distance for BGP external routes. External routes are routes for which the best path is learned from a neighbor external to the autonomous system. Accept table values are from 1 to 255. The default is 20. Routes with a distance of 255 are not installed in the routing table. 

internal-distance 

Administrative distance for BGP internal routes. Internal routes are those routes that are learned from another BGP entity within the same autonomous system. Accept table values are from 1 to 255. The default is 200. Routes with a distance of 255 are not installed in the routing table. 

local-distance 

Administrative distance for BGP local routes. Local routes are those networks listed with a network router configuration command, often as back doors, for that router or for networks that are being redistributed from another process. Accept table values are from 1 to 255. The default is 200. Routes with a distance of 255 are not installed in the routing table. 

Defaults 

external-distance: 20 

internal-distance: 200 

local-distance: 200 

In this case, the internal distance is 60 and the external is 90, and the local distance is 120 (same as RIP). 

Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/iproute/command/reference/fiprrp_r/1rfbgp1. html#wp1113874 

Answer: C 

Explanation: 

With IS-IS we will see ES-IS when one of the following is true: 

. uk.co.certification.simulator.questionpool.PList@138b7160 

So in this question because we do not know about the other side’s “show CLNS neighbor” A must be the better choose.