NEW QUESTION 1
If a GPU card is Installed in HyperFlex nodes before a cluster is created, which action can be used to automatically build the service profile in UCS Manager?

• A. Check Run UCS Manager Configuration during the cluster creation process
• B. Check the extended memory option during the cluster creation process
• C. Check the GPU workflow during the cluster creation process
• D. Check the administrative workflow option during the cluster creation process

Answer: C

Explanation:

NEW QUESTION 2
Which two steps should be performed before installing HyperFlex? (Choose two.)

• A. Determine and download recommended hypervisor
• B. Determine and download recommended VCenter required
• C. Download service profile templates
• D. Determine and download recommended UCS firmware required.
• E. Determine and download virtual machine OS' required.

Answer: AD

NEW QUESTION 3
Which two results are expected when you replace a node or expand a cluster? (Choose two.)

• A. Distributed pooled data is migrated off nodes to master data store.
• B. Affected node is marked as unhealthy and placed into standby mode
• C. vSphere DRS migrates the virtual machines to the new node to balance the load
• D. On node replace, the self-healing must finish for the cluster to be healthy
• E. The cluster profile is updated and RAID takes care of rebalancing the load.

Answer: CD

Explanation:

NEW QUESTION 4
The process of optimizing information is tightly tied to the writing process as it is performed inline as the writing process is being performed The process of data optimization is performed with which two processes? (Choose two)

• A. The primary CVM compresses the data, writes it to its cache drive and mirrors it
• B. ACK is sent to the CVM that the write is about to be initiated
• C. On write, the local lOVisor sends the write to the primary CVM for that block
• D. On read/Writ
• E. the distributed VAAI sends the write to the primary CVM for that block
• F. The secondary CVM compresses the data, reads it from its cache drive and mirrors it

Answer: AC

Explanation:

NEW QUESTION 5
Which two statements on Replication Factors are valid? (Choose two.)

• A. RF2 has 100% better protection of data while using 33% more space and is recommended.
• B. RF3 has 100% better protection of data while using 33% more space and is recommended.
• C. LAZ can increase RTO for 16+ node clusters.
• D. When performing rolling upgrades, the upgraded node is down for maintenance, stretching RF2 to the absolute limit.
• E. LAZ can decrease fault tolerance of S+ node clusters to less than 4

Answer: BD

Explanation:

NEW QUESTION 6
Which three additional management tools are included in HXDP to configure HyperFlex clusters? (Choose three.)

• A. UCS Manager
• B. Storage CLI
• C. Data Center Network Manager
• D. Cisco IMC 13
• E. REST API
• F. HyperFlex Connect

Answer: BEF

Explanation:

NEW QUESTION 7
Which three features for NVMe transfer protocol are valid? (Choose three.)

• A. Uses PCIe interface
• B. Streamlined commands for fewer CPU instructions
• C. More and deeper queues
• D. Requires 10 controller
• E. Increases memory speed for more lOPs
• F. Improves SAS and SATA speed

Answer: ABC

Explanation:

NEW QUESTION 8
Which version of HXDP was the first to support multiple VICs on a single server?

• A. HXDP 3.5.1
• B. HXDP 3.0
• C. HXDP 4.0
• D. HXDP 3.5

Answer: A

Explanation:

NEW QUESTION 9
HyperFlex compute nodes contribute what percentage of the overall disk storage capacity?

• A. 5%
• B. 20%
• C. 0%
• D. 10%

Answer: C

Explanation:

NEW QUESTION 10
Which three configurations for read caching in Cisco HyperFlex are valid? (Choose three.)

• A. Battery-Initiated Read-back (default): Only read data and most commonly used data are deposited in the Level 4 read-back cache
• B. Write-back (default): Only write information and most commonly used information are deposited in the cache
• C. Write-through (install option for VDI): Only most commonly used data is cached: optimizing VDI performance
• D. No caching (SSD): With all-flash nodes; because there is little difference in read speeds between SSDs
• E. Level 4 cached (SSD): With semi-flash nodes; there is a large difference in read speeds between SSDs
• F. Write-first (default for VDI): Infrequently used data is cached: freeing system resources for VDI performance

Answer: BCD

Explanation:

NEW QUESTION 11
Which uses for the system drive in an HX node are valid? (Choose two.)

• A. Migration
• B. Saving and restoring program state
• C. Virtual machine store
• D. Garbage collection
• E. Write Cache

Answer: BD

Explanation:

NEW QUESTION 12
What does the letter W indicate when selecting CPUs for your HX Node (le. HX-CPU 8170M)?

• A. support of 1.5 TB/socket of memory
• B. support for all flash drive array
• C. support for NVMe
• D. support for 768 TB/socket of memory

Answer: A

Explanation:

NEW QUESTION 13
What is the minimum amount of memory required for an HX node?

• A. 192 GB
• B. 64 GB
• C. 32 GB
• D. 128 GB

Answer: D

Explanation:

NEW QUESTION 14
HyperFlex uses file system native snapshots and provides which three features? (Choose three.)

• A. on datastore level, snapshots work the same as vSphere snapshots
• B. automatically deduplicating data of snapshots through StorFS
• C. impact on the VM performance after a lot of writes, requiring future administration
• D. limitations in age and number of snapshot
• E. See user manual for limitations
• F. consolidation of snapshots is still manual but not necessary
• G. automatic update to the golden image when a configuration change is made

Answer: ABD

NEW QUESTION 15
What is the maximum size of an HXDP cluster running 3.5.1?

• A. 64 nodes
• B. 8 nodes
• C. 16 nodes
• D. 32 nodes

Answer: A

Explanation:

NEW QUESTION 16
Which two Cisco UCS Servers support converged nodes in HyperFlex Data Platform (HXDP)? (Choose two.)

• A. HX 220
• B. UCSB200
• C. UCS C480
• D. UCS B480
• E. HX240

Answer: AE

Explanation:

NEW QUESTION 17
......