[2021-New] Cisco 300-101 Dumps With Update Exam Questions (10-19)

300-101 Dumps

300-101 Exam Questions - Online Test

300-101 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

P.S. Precise 300-101 questions are available on Google Drive, GET MORE: https://drive.google.com/open?id=1rlPNNoD0ZdgZsqoRN-j_tpudN825BWM5

New Cisco 300-101 Exam Dumps Collection (Question 10 - Question 19)

New Questions 10

An administrator needs to setup an NTP client to provide updates to local without synchronizing to server. What is the command?

A. Serve

B. Serve-only

C. peer

Answer: A

New Questions 11

Which command do you enter to display log messages with a timestamp that includes the length of time since the device was last rebooted?

A. service timestamps log uptime

B. logging facility 20

C. service timestamps debugging localtime msec

D. logging console errors

E. logging monitor 7

F. service timestamps log datetime msec

Answer: A

New Questions 12

Which two addresses types are included in NAT?

A. inside global

B. global outside

C. outside internet

D. inside internet

E. outside local

Answer: A,E

New Questions 13

How does an IOS router process a packet that should be switched by Cisco Express Forwarding without an FIB entry?

A. by forwarding the packet

B. by dropping the packet

C. by creating a new FIB entry for the packet

D. by looking in the routing table for an alternate FIB entry

Answer: B

New Questions 14

What is the function of the snmp-server manager command?

A. to enable the device to send and receive SNMP requests and responses

B. to disable SNMP messages from getting to the SNMP engine

C. to enable the device to send SNMP traps to the SNMP server

D. to configure the SNMP server to store log data

Answer: A

Explanation: The SNMP manager process sends SNMP requests to agents and receives SNMP responses and notifications from agents. When the SNMP manager process is enabled, the router can query other SNMP agents and process incoming SNMP traps. Most network security policies assume that routers will be accepting SNMP requests, sending SNMP responses, and sending SNMP notifications. With the SNMP manager functionality enabled, the router may also be sending SNMP requests, receiving SNMP responses, and receiving SNMP notifications. The security policy implementation may need to be updated prior to enabling this functionality.

SNMP requests are typically sent to UDP port 161. SNMP responses are typically sent from UDP port 161. SNMP notifications are typically sent to UDP port 162.

New Questions 15

Refer to the exhibit.

A network engineer is working on the network topology and executes the command no ip split-horizon on interface S0/0 of the hum router. What is the result of this command?

A. A routing loop is created.

B. Each of the spoke routers can see the routes that are advertised from the other spoke routers.

C. The Spoke routers can see the routes that are advertised by the hub router.

D. The hub router can see the routes that are advertised by the spoke routers.

Answer: B

New Questions 16

Which three protocols are supported with EVN?

A. IS-IS

B. EIGRP

C. RIP

D. OSPF

E. BFD

F. BGP

Answer: B,D,F

New Questions 17

Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose Two)

A. debug tacacs

B. debug ppp authentication

C. debug radius

D. debug aaa authentication

E. debug ppp negotiation

Answer: B,E

Explanation: http://www.cisco.com/c/en/us/support/docs/wan/point-to-point-protocol-ppp/25647-understanding-ppp-chap.html

New Questions 18

Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation?

A. rewriting of higher layer information

B. checksum verification

C. ipv6 duplication and conservation

D. IPSEC AH header modification

Answer: A

New Questions 19

Refer to the Exhibit.

All interfaces on each router are participating in the EIGRP 100 process. Interface Loopback 2 on HQ-R2 is currently in shutdown mode. An engineer issues the eigrp stub command on router BR1. Which statements about the query messages sent from router HQ-R2 for a route to reach the 12.12.12.12/32 network is true?

A. Router HQ-R2 sends a query message to the feasible successor for a route to 12.12.12.12/32 network.

B. BR1 receives query messages from HQ-R2 for a route to 12.12.12.12/32 network.

C. Router HQ-R1 receives query messages from HQ-R2 for a route to 12.12.12.12/32 network.

D. Router HQ-R1 and BR1 receives query messages from HQ-R2 for a route to 12.12.12/32 network.

Answer: D

100% Update Cisco 300-101 Questions & Answers shared by Surepassexam, Get HERE: https://www.surepassexam.com/300-101-exam-dumps.html (New 487 Q&As)