Q1. - (Topic 3) 

Which TWO components of IBM Systems Director are included in a new installation of a AIX 7.1? (Select 2) 

A. Common Agent 

B. Interface Agent 

C. Distributed Agent 

D. Platform Agent 

E. Management Agent 

F. Update Agent 

G. Compliance Agent 

View Answer

Q2. - (Topic 1) 

What is a mandatory requirement to allow an AIX 7-based NIM Master to install clients over IPv6? 

A. The NIM Master must use static IPv6 addresses. 

B. The NIM Master must have both IPv4 and IPv6 connectivity. 

C. The NIM Master must be installed with the AIX Enterprise Edition license. 

D. The NIM Master must be running at least AIX 7.1 TLOO Service Pack3 or later. 

View Answer

Q3. - (Topic 4) 

The following verification routine is part of a script used to automate cloning rootvg. This routine determines which disks are available for use. Applying the logic, what configuration of disk would be selected by the script as a candidate? 

A. A SAN disk virtualized by NPIV. 

B. A local physical SAS drive, currently a member of the vg00 volume group. 

C. A physical SATA disk drive, currently containing the altinst_rootvg volume group. 

D. A SAN disk virtualized as a Virtual SCSI disk, currently not part of a volume group 

View Answer

Q4. - (Topic 2) 

Which command will show all the logical volumes, filesystem mount points, and the volume group in which they reside? 

A. Islv-al 

B. mount-v 

C. df-vAg 

D. Isvg | Isvg -il 

View Answer

Q5. - (Topic 4) 

An administrator noticed that the hostname is being resolved incorrectly after setting up TCP/IP on multiple interfaces. Further inspection shows the /etc/hosts file has duplicate entries for the hostname associated with different IP addresses. 

Which of the following is most likely the cause of this situation? 

A. IPv6 is in use and requires a hostname for every interface. 

B. The administrator ran smitty mktcpip on multiple interfaces. 

C. The DNS configuration has multiple separate DNS servers listed. 

D. An EtherChannel was setup using 2 network interfaces as primary adapters. 

View Answer

Q6. - (Topic 4) 

Why has the following message returned when creating a NIM lpp_source from a the AIX 7100-02-01 Service Pack? 

A. The lpp_source was not created using base media. 

B. A source repository was not included in the command. 

C. The bos.rte fileset was not included in the lpp_source. 

D. The simage attribute was not specified in the command 

View Answer

Q7. - (Topic 4) 

When could an IVM instance be preferable to an HMC for Power Systems management? 

A. Where multiple partition profiles are required 

B. When Systems Director is used for central management 

C. Where Power Compute Nodes are deployed in a PureFlex environment 

D. When a single entry level Power Systems server needs to be split into LPARs 

View Answer

Q8. - (Topic 2) 

An administrator migrated a global environment of AIX 6 to AIX 7 using NIM. They have attempted to use the migwpar command to migratea selection of hosted WPARs from AIX 6 to AIX 7, but a detached system WPAR fails to migrate to AIX 7. 

How can a detached system WPAR be migrated to AIX 7? 

A. NIM 

B. AIX install media 

C. savewpar command 

D. syncwpar command 

View Answer

Q9. - (Topic 1) 

The following information has been reported in an AIX error log: 

How can the administrator prevent the error from reoccurring? 

A. Create a secondary dump device greater than 266MB 

B. Increase primary dump device size greater than 266MB 

C. Increase “/var" file system to ensure it has a minimum of 266MB free space 

D. Increase "/var/adm/ras/livedump" file system to ensure it has a minimum of 266MB free space 

View Answer

Q10. - (Topic 2) 

The/usr/sbin/clcmd command is not working as documented in an administrator's reference. How can the administrator determine if the command being run is at the same level as the command being referenced in the documentation? 

A. Get the fileset name from Isipp-f, then check the level of the file set with lslpp-1. 

B. Use Islpp-wto get the fileset name, then check the level of the file set with lslpp-1. 

C. Use lslpp-1 to determine the fileset name and check the level. 

D. Use Is-I to determine the last modified date of the command. 

View Answer