Q1. DRAG DROP
Drag and drop each fast detection mechanism on the left to its definition on the right.
Answer:
Q2. Refer to the exhibit. R1 and R2 are multicast routers running PIM over Serial1/0. The PIM adjacency on R1 is not forming with the given configuration. What command can be entered on R1 to resolve the issue?
A. no access-list 100 deny 103 any any
B. no access-list 100 deny udp any anyeq 103
C. no access-list 100 deny ip any host 224.0.0.1
D. no access-list 100 deny ip any host 224.0.0.2
Answer: A
Explanation:
All PIM protocols share a common control message format. PIM control messages are sent as raw IP datagrams (protocol number 103), either multicast to the link-local ALL PIM
ROUTERS multicast group, or unicast to a specific destination.
Reference: http://www.metaswitch.com/resources/what-is-protocol-independent-multicast-pim
Q3. Refer to the exhibit. Customer XYZ Site 1 is not learning prefixes from Site 2. What is the issue?
A. MPLS LSP is broken along the path.
B. The route-policy is not implemented in router PE-2.
C. The BGP local-as command should be used between PE-1 and CE-1.
D. The route-distinguisher values must match in both sites.
E. The BGP as-override command should be implemented between PE-1 and CE-1.
Answer: E
Q4. Refer to the exhibit. The referenced TE tunnels compete for bandwidth requirements over the limited available bandwidth that is provisioned. Which core MPLS component erases a conflict and provides admission control for any new added TE tunnel?
A. link management
B. link attributes
C. MPLS TE priorities
D. RSVP
Answer: D
Explanation: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/mpls/configuration/guide/mpls_cg/mp_te_RSVP.pdf
Q5. SSO was configured on a Cisco ASR 1006 Router by using two RPs. When the main RP failed, a service disruption occurred. What are two reasons that the SSO did not work? (Choose two.)
A. The standby RP has a different DRAM configuration than the primary RP.
B. HSRP and NSF are not configured.
C. The ESP that is installed in the Cisco ASR 1006 Router does not support SSO.
D. The standby RP was not ready to switch over when the primary RP failed.
E. The standby RP has a different IOS version than the primary RP.
Answer: B,E
Explanation:
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/configuration/guide/chassis/asrswcfg /High_Availability.html
Q6. Which two statements about Unified MPLS are true? (Choose two.)
A. Unified MPLS works on Cisco IOS XR Software only.
B. Unified MPLS extends MPLS across multidomain networks in a scalable manner.
C. New technologies or protocols are not used; only MPLS, LDP, IGP, and BGP are used.
D. ABR loopback prefixes should always be redistributed from the core IGP into the aggregation IGP.
E. The RRs are part of the control path only.
Answer: B,D
Explanation: http://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/mpls/116127-configure-technology-00.pdf
Q7. An engineer is working to provide high availability to a Service Provider core network. Which BGP command enables a backup path to be installed in the RIB and CEF tables?
A. maximum-paths ibgp
B. bgp additional-paths install
C. maximum-paths eibgp
D. bgp additional-paths select
E. bgp advertise-best-external
Answer: B
Explanation: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/configuration/xe-3s/irg-xe-3s-book/bgp_best_external.html#GUID-66F31B75-B1E6-4B38-9B4D-6A89839930CE
Q8. A network engineer needs to connect two core switches that use Gigabit Ethernet interfaces in an MPLS backbone and that are separated by a distance of 60 km. Which Cisco GBIC achieves this goal?
A. Cisco 1000BASE-T GBIC
B. Cisco 1000BASE-SX GBIC
C. Cisco 1000BASE-LX/LH GBIC
D. Cisco 1000BASE-ZX GBIC
Answer: D
Explanation:
http://www.cisco.com/web/partners/downloads/765/tools/quickreference/gbic.pdf
Q9. In Multicast Inter-AS VPN context, which BGP attribute should you use to overcome the Option B limitation due to a rewritten originator next-hop address in the network?
A. connector
B. AS path
C. weight
D. originator
Answer: A
Q10. Refer to the exhibit.
A service provider has multiple time sources in the environment for NTP. The time source at 10.0.4.1 is intended to be seen as a primary time source. What command can be issued on PE4 to fix the configuration, ensuring the proper NTP source will be issued?
A. ntp peer 10.0.4.1
B. ntp peer 10.0.4.1 prefer
C. ntp server 10.0.4.1 source GigabitEthernet0/0
D. ntp server 10.0.4.1 prefer
Answer: D
Explanation: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/system_management/configuration/guide/sm_nx_os_cg/sm_3ntp.html#wp1106725