P.S. Accurate 200-125 vce are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials
New Questions 3
Refer to the exhibit.
While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?
A. the percentage of use of the link
B. the preference of the link
C. the session count of the link
D. the number source-destination pairs on the link
Answer: D
New Questions 4
R1#show running-config interface Loopback0
description ***Loopback***
ip address 192.168.1.1 255.255.255.255
ip ospf 1 area 0
!
interface Ethernet0/0
description **Connected to R1-LAN** ip address 10.10.110.1 255.255.255.0
ip ospf 1 area 0
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.1 255.255.255.0
ip ospf hello-interval 25 ip ospf 1 area 0
!
router ospf 1
log-adjacency-changes
R2# show running-config R2
!
interface Loopback0 description **Loopback**
ip address 192.168.2.2 255.255.255.255
ip ospf 2 area 0
!
interface Ethernet0/0
description **Connected to R2-LAN** ip address 10.10.120.1 255.255.255.0
ip ospf 2 area 0
!
interface Ethernet0/1
description **Connected to L2SW**
ip address 10.10.230.2 255.255.255.0
ip ospf 2 area 0
!
router ospf 2
log-adjacency-changes
R3#show running-config R3
username R6 password CISCO36
!
interface Loopback0 description **Loopback**
ip address 192.168.3.3 255.255.255.255
ip ospf 3 area 0
!
interface Ethernet0/0
description **Connected to L2SW**
ip address 10.10.230.3 255.255.255.0
ip ospf 3 area 0
!
interface Serial1/0
description **Connected to R4-Branch1 office** ip address 10.10.240.1 255.255.255.252
encapsulation ppp ip ospf 3 area 0
!
interface Serial1/1
description **Connected to R5-Branch2 office** ip address 10.10.240.5 255.255.255.252
encapsulation ppp
ip ospf hello-interval 50 ip ospf 3 area 0
!
interface Serial1/2
description **Connected to R6-Branch3 office** ip address 10.10.240.9 255.255.255.252
encapsulation ppp ip ospf 3 area 0
ppp authentication chap
!
router ospf 3
router-id 192.168.3.3
!
R4#show running-config
R4
!
interface Loopback0 description **Loopback**
ip address 192.168.4.4 255.255.255.255
ip ospf 4 area 2
!
interface Ethernet0/0
ip address 172.16.113.1 255.255.255.0
ip ospf 4 area 2
!
interface Serial1/0
description **Connected to R3-Main Branch office** ip address 10.10.240.2 255.255.255.252
encapsulation ppp ip ospf 4 area 2
!
router ospf 4
log-adjacency-changes
R5#show running-config R5
!
interface Loopback0 description **Loopback**
ip address 192.168.5.5 255.255.255.255
ip ospf 5 area 0
!
interface Ethernet0/0
ip address 172.16.114.1 255.255.255.0
ip ospf 5 area 0
!
interface Serial1/0
description **Connected to R3-Main Branch office**
ip address 10.10.240.6 255.255.255.252
encapsulation ppp ip ospf 5 area 0
!
router ospf 5
log-adjacency-changes
R6#show running-config R6
username R3 password CISCO36
!
interface Loopback0 description **Loopback**
ip address 192.168.6.6 255.255.255.255
ip ospf 6 area 0
!
interface Ethernet0/0
ip address 172.16.115.1 255.255.255.0
ip ospf 6 area 0
!
interface Serial1/0
description **Connected to R3-Main Branch office** ip address 10.10.240.10 255.255.255.252
encapsulation ppp ip ospf 6 area 0
ppp authentication chap
!
router ospf 6
router-id 192.168.3.3
!
R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue?
A. R1 ethernet0/1 is shutdown. Configure the no shutdown command.
B. R1 ethernet0/1 configured with a non-default OSPF hello interval of 25, configure no ip ospf hello interval 25
C. R2 ethernet0/1 and R3 ethernet0/0 are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello interval 25
D. Enable OSPF for R1 ethernet0/1; configure ip ospf 1 area 0 command under ethernet0/1
Answer: B
New Questions 5
Which two authentication methods are compatible with MLPPP on a serial interface? (Choose two.)
A. LEAP
B. PEAP
C. CHAP
D. TACACS+
E. PAP
Answer: C,E
Explanation: PPP Authentication Methods
In this part we will learn more about two authentication methods used in Authentication Phase of PPP.
PPP has two built-in security mechanisms which are Password Authentication Protocol (PAP) andChallenge Handshake Authentication Protocol (CHAP).
New Questions 6
Which switching method duplicates the first six bytes of a frame before making a switching decision?
A. fragment-free switching
B. store and-forward switching
C. cut through switching
D. ASIC switching
Answer: C
Explanation: Cut and Through method has lowest latency. In this method Switch only read first six bytes from frame after the preamble. These six bytes are the destination address of frame. This is the fastest method of switching. This method also processes invalid frames. Only advantage of this method is speed.
New Questions 7
What are the two minimum required components of a DHCP binding? (Choose two.)
A. a DHCP pool
B. an exclusion list
C. a hardware address
D. an IP address
E. an ip-helper statement
Answer: C,D
New Questions 8
Which routing protocol has the smallest default administrative distance?
A. IBGP
B. OSPF
C. IS-IS
D. EIGRP
E. RIP
Answer: D
Explanation: http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol- bgp/15986-admin-distance.html
Default Distance Value Table
This table lists the administrative distance default values of the protocols that Cisco supports:
Route Source
Default Distance Values
Connected interface 0
Static route 1
Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5
External Border Gateway Protocol (BGP) 20
Internal EIGRP 90
IGRP 100 OSPF
110
Intermediate System-to-Intermediate System (IS-IS) 115
Routing Information Protocol (RIP) 120
Exterior Gateway Protocol (EGP) 140
On Demand Routing (ODR) 160
External EIGRP 170
Internal BGP 200
Unknown* 255
New Questions 9
Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?
A. show ipv6 eigrp 20 interfaces
B. show ipv6 route eigrp
C. show ipv6 eigrp neighbors
D. show ip eigrp traffic
Answer: C
New Questions 10
What is the effect of the overload keyword in a static NAT translation configuration?
A. It enables port address translation.
B. It enables the use of a secondary pool of IP addresses when the first pool is depleted.
C. It enables the inside interface to receive traffic.
D. It enables the outside interface to forward traffic.
Answer: A
New Questions 11
Which device allows users to connect to the network using a single or double radio?
A. access point
B. switch
C. wireless controller
D. firewall
Answer: A
New Questions 12
Which two features can dynamically assign IPv6 addresses? (Choose two.)
A. IPv6 stateless autoconfiguration
B. DHCP
C. NHRP
D. IPv6 stateful autoconfiguration
E. ISATAP tunneling
Answer: A,B
P.S. Easily pass 200-125 Exam with Examcollection Accurate Dumps & pdf vce, Try Free: http://www.examcollectionuk.com/200-125-vce-download.html (889 New Questions)