Question No: 1

Refer to the exhibit.

Which rule does the DHCP server use when there is an IP address conflict?

A. The address is removed from the pool until the conflict is resolved.

B. The address remains in the pool until the conflict is resolved.

C. Only the IP detected by Gratuitous ARP is removed from the pool.

D. Only the IP detected by Ping is removed from the pool.

E. The IP will be shown, even after the conflict is resolved.

View Answer

Question No: 2

CORRECT TEXTA network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.

The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.

Access to the router CLI can be gained by clicking on the appropriate host.

All passwords have been temporarily set to "cisco".

The Core connection uses an IP address of 198.18.247.65

The computers in the Hosts LAN have been assigned addresses of 192.168.240.1 - 192.168.240.254

u2711 host A 192.168.240.1

u2711 host B 192.168.240.2

u2711 host C 192.168.240.3

View Answer

Question No: 3

Scenario

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.

An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?

A. There is an area ID mismatch.

B. There is a PPP authentication issue; a password mismatch.

C. There is an OSPF hello and dead interval mismatch.

D. There is a missing network command in the OSPF process on R5.

View Answer

Question No: 4

What command instructs the device to timestamp Syslog debug messages in milliseconds?

A. service timestamps log datetime localtime<input type

B. service timestamps debug datetime msec<input type

C. service timestamps debug datetime localtime<input type

D. service timestamps log datetime msec

View Answer

Question No: 5

How does a DHCP server dynamically assign IP addresses to hosts?

A. Addresses are permanently assigned so that the host uses the same address at all times.

B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.

C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.

D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.

View Answer

Question No: 6

What are the Populardestinations for syslog messages to be saved? (Choose three)

A. Flash

B. The logging buffer .RAM

C. The console terminal

D. Other terminals

E. Syslog server

View Answer

Question No: 7

CORRECT TEXTCCNA.com has a small network that is using EIGRP as its IGP. All routers should be running an EIGRP AS number of 12. Router MGT is also running static routing to the ISP.

CCNA.com has recently added the ENG router. Currently, the ENG router does not have connectivity to the ISP router. All over interconnectivity and Internet access for the existing locations of the company are working properly.

The taskis to identify the fault(s) and correct the router configuration(s) to provide full connectivity between the routers.

Access to the router CLI can be gained by clicking on the appropriate host.

All passwords on all routers arecisco.

IP addresses are listed in the chart below.

MGT

Fa0/0 u2013 192.168.77.33

S1/0 u2013 198.0.18.6

S0/0 u2013 192.168.27.9

S0/1 u2013 192.168.50.21

ENG

Fa0/0 u2013 192.168.77.34

Fa1/0 u2013 192.168.12.17

Fa0/1 u2013 192.168.12.1

Parts1

Fa0/0 u2013 192.168.12.33

Fa0/1 u2013 192.168.12.49

S0/0 u2013 192.168.27.10

Parts2

Fa0/0 u2013 192.168.12.65

Fa0/1 u2013 192.168.12.81

S0/1 u2013 192.168.50.22

View Answer

Question No: 8

Scenario

Refer to the topology. Your company has connected the routers R1, R2, and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5.

The EIGRP routing protocol is configured.

You are required to troubleshoot and resolve the EIGRP issues between the various routers.

Use the appropriate show commands to troubleshoot the issues.

Which path does traffic take from R1 to R5?

A. The traffic goes through R2.

B. The traffic goes through R3.

C. The traffic is equally load-balanced over R2 and R3.

D. The traffic is unequally load-balanced over R2 and R3.

View Answer

Question No: 9

Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)

A. Global addresses start with 2000::/3.

B. Link-local addresses start with FE00:/12.

C. Link-local addresses start with FF00::/10.

D. There is only one loopback address and it is ::1.

E. If a global address is assigned to an interface, then that is the only allowable address for the interface.

View Answer

Question No: 10

Which statement about access lists that are applied to an interface is true?

A. You can place as many access lists as you want on any interface.

B. You can apply only one access list on any interface.

C. You can configure one access list, per direction, per Layer 3 protocol.

D. You can apply multiple access lists with the same protocol or in different directions.

View Answer