Answer: A,D,F

Explanation:

Ping, show ip route, and show interfaces are all valid troubleshooting IOS commands. Tracert, ipconfig, and winipcfg are PC commands, not IOS.

Answer: D

Explanation:

Now letu2021s find out the range of the networks on serial link: For the network 192.168.1.62/27:

Increment: 32

Network address: 192.168.1.32

Broadcast address: 192.168.1.63 For the network 192.168.1.65/27: Increment: 32

Network address: 192.168.1.64

Broadcast address: 192.168.1.95

-> These two IP addresses donu2021t belong to the same network and they canu2021t see each other.

Answer: C

Explanation:

An agent can send unsolicited traps to the manager. Traps are messages alerting the SNMP manager to a condition on the network. Traps can mean improper user authentication, restarts, link status (up or down), MAC address tracking, closing of a TCP connection, loss of connection to a neighbor, or other significant events.

Reference: http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2950/software/release/12- 1_9_ea1/configuration/guide/scg/swsnmp.html

Answer: D

Explanation:

We only enable PortFast feature on access ports (ports connected to end stations). But if someone does not know he can accidentally plug that port to another switch and a loop may occur when BPDUs are being transmitted and received on these ports.

With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent a loop.

Answer: D

Explanation:

You must configure all interfaces in an EtherChannel to operate at the same speeds and duplex modes. Based on the output shown, SW1 is configured to run at 10Mb while SW2 is operating at 100 Mb.

Answer: B

Explanation:

Netflow can be used to diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with command line interface or reporting tools.

Reference: http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html

Answer: B

Explanation:

Members of a GLBP group elect one gateway to be the active virtual gateway (AVG) for that group. Other group members provide backup for the AVG in the event that the AVG becomes unavailable. The AVG assigns a virtual MAC address to each member of the GLBP group. Each gateway assumes responsibility for forwarding packets sent to the virtual MAC address assigned to it by the AVG. These gateways are known as active virtual forwarders (AVFs) for their virtual MAC address.

The AVG is responsible for answering Address Resolution Protocol (ARP) requests for the virtual IP address. Load sharing is achieved by the AVG replying to the ARP requests with different virtual MAC addresses.

Reference: http://www.cisco.com/en/US/docs/ios/12_2t/12_2t15/feature/guide/ft_glbp.html

Answer: B

Explanation:

In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning. When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC addresses.

Answer: D

Explanation:

The DHCP lifecycle consists of the following:

u2711 Allocation:A client begins with no active lease, and hence, no DHCP-assigned address. It acquires a lease through a process ofallocation.

u2711 Reallocation:If a client already has an address from an existing lease, then when it reboots or starts up after being shut down, it will contact the DHCP server that granted it the lease to confirm the lease and acquire operating parameters. This is sometimes calledreallocation; it is similar to the full allocation process but shorter.

u2711 Normal Operation:Once a lease is active, the client functions normally, using its assigned IP address and other parameters during the u201cmain partu201d of the lease. The client is said to beboundto the lease and the address.

u2711 Renewal:After a certain portion of the lease time has expired, the client will attempt to contact the server that initially granted the lease, torenewthe lease so it can

keep using its IP address.

u2711 Rebinding.If renewal with the original leasing server fails (because, for example, the server has been taken offline), then the client will try torebindto any active DHCP server, trying to extend its current lease with any server that will allow it to do so.

u2711 Release:The client may decide at any time that it no longer wishes to use the IP address it was assigned, and may terminate the lease,releasingthe IP address.

Answer:

The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from 198.18.184.105 to 198.18.184.110/29. Therefore we have to use NAT overload (or PAT)

Double click on the Weaver router to open it

Router>enable Router#configure terminal

First you should change the router's name to Weaver

Router(config)#hostname Weaver

Create a NAT pool of global addresses to be allocated with their netmask. Weaver(config)#ip nat pool mypool 198.18.184.105 198.18.184.110 netmask 255.255.255.248

Create a standard access control list that permits the addresses that are to betranslated.

Weaver(config)#access-list 1 permit 192.168.100.16 0.0.0.15

Establish dynamic source translation, specifying the access list that was definedin the prior step.

Weaver(config)#ip nat inside source list 1 pool mypool overload

This command translates all source addresses that pass access list 1, which means a source address from 192.168.100.17 to 192.168.100.30, into an address from the pool

named mypool (the pool contains addresses from198.18.184.105 to 198.18.184.110). Overloadkeyword allows to map multiple IP addresses to a single registered IPaddress (many-to-one) by using different ports.

The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements.

This is how to configure the NAT inside and NAT outside, just for yourunderstanding:

Weaver(config)#interface fa0/0 Weaver(config-if)#ip nat inside Weaver(config-if)#exit Weaver(config)#interface s0/0 Weaver(config-if)#ip nat outside Weaver(config-if)#end

Finally, we should save all your work with the following command:

Weaver#copy running-config startup-config

Check your configuration by going to "Host for testing" and type:

C :\>ping 192.0.2.114

The ping should work well and you will be replied from 192.0.2.114