Q1. Which two statements about Ethernet standards are true? (Choose two)

A. Ethernet is defined by IEEE standard 802.2.

B. Ethernet is defined by IEEE standard 802.3.

C. Ethernet 10BASE-T does not support full-duplex.

D. When an Ethernet network uses CSMA/CD, it terminates transmission as soon as a

collision occurs.

E. When an Ethernet network uses CSMA/CA. it terminates transmission as soon as a collision occurs.

View Answer

Q2. Which command can you enter to troubleshoot the failure of address assignments?

A. show ip dhcp pool

B. show ip dhcp database

C. show ip dhcp import

D. clear ip dhcp server statistics

View Answer

Q3. What are three advantages of vlans ?

A. They provide a method of conserving ip addresses in large networks

B. They provide a low latency internetworking alternative to routed networks

C. they utilize packet filtering to enhance network security

D. They establish broadcast domains in switched networks

E. They allow access to network services based on department not physical localtion

F. They can simplify adding moving or changing hosts on the network

View Answer

Q4. Which two options are fields in an ethernet frame ? choose two

A. destination ip address

B. source ip address

C. type

D. frame check sequence

E. header

View Answer

Q5. refer to the exhibit:

what is the metric for the router from R1 to 192.168.10.1 ?

A. 2

B. 90

C. 110

D. 52778

View Answer

Q6. Which two statements about access points are true? (Choose Two)

A. They can provide access within enterprises and to the public.

B. in Most cases, they are physically connected to other network devices to provide network connectivity.

C. They can proterct a network from internal and external threats.

D. Most access points provide Wi-Fi and Bluetooth connectivity.

E. They must be hardwired to a modem.

View Answer

Q7. Which command can you enter to determine whether a switch is operating in trunking mode?

A. show ip interface brief

B. show vlan

C. show interfaces

D. show interface switchport

View Answer

Q8. Scenario:

You work for a company that provides managed network services, and of your real estate clients running a small office is experiencing network issues, Troubleshoot the network issues.

Router R1 connects the main office to internet, and routers R2 and R3 are internal routers NAT is enabled on Router R1.

The routing protocol that is enable between routers R1, R2, and R3 is RIPv2.

R1 sends default route into RIPv2 for internal routers to forward internet traffic to R1. Server1 and Server2 are placed in VLAN 100 and 200 respectively, and dare still running

router on stick configuration with router R2.

You have console access on R1, R2, R3, and L2SW1 devices. Use only show commands to troubleshoot the issues.

What is the correct statement below after examining the R1 routing table?

A. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses static route instead RIPv2 Because the static route AD that is configured is less than the AD of RIPv2

B. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses RIPv2 instead static

route Because the static route AD that is configured is higher than the AD of RIPv2

C. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses static route instead RIPv2 But the traffic is forwarded to the ISP instead of the internal network.

D. Traffic that is destined to 10.10.10.0/24 from R1 LAN network uses RIPv2 instead static route Because the static route AD that is configured is 255

View Answer

Q9. Which address class includes network 191.168.0.1/27?

A. Class C

B. Class B

C. Class D

D. Class A

View Answer

Q10. Which DTP switch port mode allows the port to create a trunk link if the neighboring port is in trunk mode, dynamic desirable mode, or desirable auto mode?

A. trunk

B. access

C. dynamic desirable

D. dynamic auto

View Answer