[2021-New] Cisco 200-125 Dumps With Update Exam Questions (5-14)

200-125 Dumps

200-125 Exam Questions - Online Test

200-125 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

P.S. Verified 200-125 free samples are available on Google Drive, GET MORE: https://drive.google.com/open?id=1h4WwjNBP_fjjnxXJLxNgPsEiO-cPwGBa

New Cisco 200-125 Exam Dumps Collection (Question 5 - Question 14)

New Questions 5

What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.)

A. The interface displays a connected (up/up) state even when the duplex settings are mismatched.

B. The symptoms of a duplex mismatch may be intermittent.

C. Autonegotiation is disabled.

D. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions.

E. 1-Gbps interfaces are full-duplex by default.

Answer: A,B

New Questions 6

Scenario:

You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

NAT is enabled on router R1.

The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?

A. Interesting traffic for NAT ACL is incorrectly configured.

B. NAT configurations on the interfaces are incorrectly configured

C. NAT translation statement incorrectly configured.

D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.

Answer: B

New Questions 7

Which component of a routing table entry represents the subnet mask?

A. routing protocol code

B. prefix

C. metric

D. network mask

Answer: D

Explanation:

IP Routing Table Entry Types

An entry in the IP routing table contains the following information in the order presented: Network ID.The network ID or destination corresponding to the route. The network ID can be class-based, subnet, or supernet network ID, or an IP address for a host route. Network Mask.The mask that is used to match a destination IP address to the network ID. Next Hop.The IP address of the next hop.

Interface.An indication of which network interface is used to forward the IP packet. Metric.A number used to indicate the cost of the route so the best route among possible multiple routes to the same destination can be selected. A common use of the metric is to indicate the number of hops (routers crossed) to the network ID.

Routing table entries can be used to store the following types of routes:

Directly Attached Network IDs.Routes for network IDs that are directly attached. For directly attached networks, the Next Hop field can be blank or contain the IP address of the interface on that network.

Remote Network IDs.Routes for network IDs that are not directly attached but are available across other routers. For remote networks, the Next Hop field is the IP address of a local router in between the forwarding node and the remote network.

Host Routes.A route to a specific IP address. Host routes allow routing to occur on a per-

IP address basis. For host routes, the network ID is the IP address of the specified host and the network mask is 255.255.255.255.

Default Route.The default route is designed to be used when a more specific network ID or host route is not found. The default route network ID is 0.0.0.0 with the network mask of 0.0.0.0.

New Questions 8

Refer to the exhibit.

Router edge-1 is unable to establish OSPF neighbor adjacency with router ISP-1. Which two configuration changes can you make on edge-1 to allow the two routers to establish adjacency? (Choose two.)

A. Set the subnet mask on edge-1 to 255 255.255.252.

B. Reduce the MTU on edge-1 to 1514.

C. Set the OSPF cost on edge-1 to 1522.

D. Reduce the MTU on edge-1 to 1500.

E. Configure the ip ospf mtu-ignore command on the edge-1 Gi0/0 interface.

Answer: D,E

Explanation: A situation can occur where the interface MTU is at a high value, for example 9000, while the real value of the size of packets that can be forwarded over this interface is 1500.

If there is a mismatch on MTU on both sides of the link where OSPF runs, then the OSPF adjacency will not form because the MTU value is carried in the Database Description (DBD) packets and checked on the other side.

New Questions 9

Which feature can you use to monitor traffic on a switch by replicating it to another port or ports on the same switch?

A. copy run start

B. traceroute

C. the ICMP Echo IP SLA

D. SPAN

Answer: D

Explanation: A source port, also called a monitored port, is a switched or routed port that you monitor for network traffic analysis. In a single local SPAN session or RSPAN source session, you can monitor source port traffic, such as received (Rx), transmitted (Tx), or bidirectional (both). The switch supports any number of source ports (up to the maximum number of available ports on the switch) and any number of source VLANs.

A source port has these characteristics:

u2711 It can be any port type, such as EtherChannel, Fast Ethernet, Gigabit Ethernet, and so forth.

u2711 It can be monitored in multiple SPAN sessions.

u2711 It cannot be a destination port.

u2711 Each source port can be configured with a direction (ingress, egress, or both) to monitor. For EtherChannel sources, the monitored direction applies to all physical

ports in the group.

u2711 Source ports can be in the same or different VLANs.

u2711 For VLAN SPAN sources, all active ports in the source VLAN are included as source ports.

New Questions 10

Under normal operations, Cisco recommends that you configure switchports on which VLAN?

A. on any VLAN except the default VLAN

B. on the management VLAN

C. on the native VLAN

D. on the default VLAN

Answer: D

New Questions 11

Which type of address is the public IP address of a NAT device?

A. outside global

B. outside local

C. inside global

D. inside local

E. outside public

F. inside public

Answer: C

New Questions 12

What is the danger of the permit any entry in a NAT access list?

A. It can lead to overloaded resources on the router.

B. It can cause too many addresses to be assigned to the same interface.

C. It can disable the overload command.

D. It prevents the correct translation of IP addresses on the inside network.

Answer: A

New Questions 13

When an interface is configured with PortFast BPDU guard, how does the interface respond when it receives a BPDU?

A. It continues operating normally.

B. It goes into a down/down state.

C. It becomes the root bridge for the configured VLAN.

D. It goes into an errdisable state.

Answer: D

New Questions 14

Which three commands can you use to set a router boot image? (Choose three.)

A. Router(config)# boot system flash c4500-p-mz.121-20.bin

B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin

C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin

D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin

E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin

F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin

Answer: A,B,C

P.S. Easily pass 200-125 Exam with Examcollection Verified Dumps & pdf vce, Try Free: http://www.examcollectionuk.com/200-125-vce-download.html (890 New Questions)