[2021-New] Cisco 200-125 Dumps With Update Exam Questions (9-18)

200-125 Dumps

200-125 Exam Questions - Online Test

200-125 Premium VCE File

Learn More 100% Pass Guarantee - Dumps Verified - Instant Download
150 Lectures, 20 Hours

P.S. Highest Quality 200-125 vce are available on Google Drive, GET MORE: https://drive.google.com/open?id=1G0OQvn58oVaFHU8QUjdLariF4zPSu0BB

New Cisco 200-125 Exam Dumps Collection (Question 9 - Question 18)

Q1. Scenario:

You work for a company that provides managed network services, and of your real estate clients running a small office is experiencing network issues, Troubleshoot the network issues.

Router R1 connects the main office to internet, and routers R2 and R3 are internal routers NAT is enabled on Router R1.

The routing protocol that is enable between routers R1, R2, and R3 is RIPv2.

R1 sends default route into RIPv2 for internal routers to forward internet traffic to R1. Server1 and Server2 are placed in VLAN 100 and 200 respectively, and dare still running

router on stick configuration with router R2.

You have console access on R1, R2, R3, and L2SW1 devices. Use only show commands to troubleshoot the issues.

Users in the main office complain that they are unable to reach internet sites.

You observe that internet traffic that is destined towards ISP router is not forwarded correctly on Router R1. What could be an issue?

Ping to Internet server shows the following results from R1: R1#ping 209.165.200.225

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 209.165.200.225. timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

A. The next hop router address for the default route is incorrectly configured.

B. Default route pointing to ISP router is configured with AD of 255.

C. Default route pointing to ISP router is not configured on Router R1

D. Router R1 configured as DHCP client is not receiving default route via DHCP from ISP router.

Answer: C

Explanation:

(Default Static Route will fix the problem to connect to ISP router)

Q2. Which two statements about wireless LAN controllers are true? (Choose two.)

A. They can simplify the management and deployment of wireless LANs.

B. They rely on external firewalls for WLAN security.

C. They are best suited to smaller wireless networks.

D. They must be configured through a GUI over HTTP or HTTPS.

E. They can manage mobility policies at a systemwide level.

Answer: A,E

Q3. Which statement about named ACLs is true?

A. They support standard and extended ACLs.

B. They are used to filter usernames and passwords for Telnet and SSH.

C. They are used to filter Layer 7 traffic.

D. They support standard ACLs only.

E. They are used to rate limit traffic destined to targeted networks.

Answer: A

Explanation:

Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.

Q4. Which three statements about IPv6 prefixes are true? (Choose three.)

A. FF00:/8 is used for IPv6 multicast.

B. FE80::/10 is used for link-local unicast.

C. FC00::/7 is used in private networks.

D. 2001::1/127 is used for loopback addresses.

E. FE80::/8 is used for link-local unicast.

F. FEC0::/10 is used for IPv6 broadcast.

Answer: A,B,C

Q5. Which configuration can you apply to enable encapsulation on a subinterface?

A. interface FastEthernet 0/0 encapsulation dot1Q 30

ip address 10.1.1.30 255.255.255.0

B. interface FastEthernet 0/0.30

ip address 10.1.1.30 255.255.255.0

C. interface FastEthernet 0/0.30 description subinterface vlan 30

D. interface FastEthernet 0/0.30 encapsulation dot1Q 30

ip address 10.1.1.30 255.255.255.0

Answer: D

Q6. Which spanning-tree feature places a port immediately into a forwarding stated?

A. BPDU guard

B. PortFast

C. loop guard

D. UDLD

E. Uplink Fast

Answer: B

Explanation:

PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states.You can use PortFast on switch or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.

Q7. Which command can you enter to verify that a BGP connection to a remote device is established?

A. show ip bgp summary

B. show ip community-list

C. show ip bgp paths

D. show ip route

Answer: A

Q8. Which protocol advertises a virtual IP address to facilitate transparent failover of a Cisco routing device?

A. FHRP

B. DHCP

C. RSMLT

D. ESRP

Answer: A

Q9. Which statement about routing protocols is true?

A. Link-state routing protocols choose a path by the number of hops to the destination.

B. OSPF is a link-state routing protocol.

C. Distance-vector routing protocols use the Shortest Path First algorithm.

D. IS-IS is a distance-vector routing protocol.

Answer: B

Explanation: Link State Routing Protocols

Link state protocols are also called shortest-path-first protocols. Link state routing protocols have a complete picture of the network topology. Hence they know more about the whole network than any distance vector protocol.

Three separate tables are created on each link state routing enabled router. One table is used to hold details about directly connected neighbors, one is used to hold the topology of the entire internetwork and the last one is used to hold the actual routing table.

Link state protocols send information about directly connected links to all the routers in the network. Examples of Link state routing protocols includeOSPF - Open Shortest Path FirstandIS-IS - Intermediate System to Intermediate System.

There are also routing protocols that are considered to be hybrid in the sense that they use aspects of both distance vector and link state protocols.EIGRP - Enhanced Interior Gateway Routing Protocolis one of those hybrid routing protocols.

Q10. Which option describes a benefit of a point-to-point leased line?

A. full-mesh capability

B. flexibility of design

C. low cost

D. simplicity of configuration

Answer: D

P.S. Easily pass 200-125 Exam with Surepassexam Highest Quality Dumps & pdf vce, Try Free: https://www.surepassexam.com/200-125-exam-dumps.html (889 New Questions)