Q1. Which statement about using EtherChannel on Cisco IOS switches is true?

A. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.

B. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 8 Gbps only for Gigabit EtherChannel.

C. A switch can support up to eight compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 800 Mbps only for Fast EtherChannel or 16 Gbps only for Gigabit EtherChannel.

D. A switch can support up to 10 compatibly configured Ethernet interfaces in an EtherChannel. The EtherChannel provides full-duplex bandwidth up to 1000 Mbps only for Fast EtherChannel or 10 Gbps only for Gigabit EtherChannel.

View Answer

Q2. In which portion of the frame is the 802.1q header found?

A. within the Ethernet header

B. within the Ethernet payload

C. within the Ethernet FCS

D. within the Ethernet source MAC address

View Answer

Q3. Which statement about LLDP-MED is true?

A. LLDP-MED is an extension to LLDP that operates between endpoint devices and network devices.

B. LLDP-MED is an extension to LLDP that operates only between network devices.

C. LLDP-MED is an extension to LLDP that operates only between endpoint devices.

D. LLDP-MED is an extension to LLDP that operates between routers that run BGP.

View Answer

Q4. Refer to the exhibit.

All ports are members of VLAN 10. Considering the default cost of upstream bridges to the root bridge is equal, which option will be the new root port for VLAN 10?

A. interface f0/13

B. interface f0/14

C. interface f0/15

D. interface f0/21

View Answer

Q5. Which statement describes what happens when a switch enters dual active recovery mode?

A. The switch shuts down and waits for the VSL link to be restored before sending traffic.

B. All interfaces are shut down in the formerly active virtual switch member, but the new active virtual switch forwards traffic on all links.

C. The switch continues to forward traffic out all links and enables spanning tree on VSL link and all other links to prevent loops.

D. The VSS detects which system was last in active state and shuts down the other switch.

View Answer

Q6. A network engineer wants to add a new switch to an existing switch stack. Which configuration must be added to the new switch before it can be added to the switch stack?

A. No configuration must be added.

B. stack ID

C. IP address

D. VLAN information

E. VTP information

View Answer

Q7. Which protocol specified by RFC 2281 provides network redundancy for IP networks, ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits?

A. ICMP

B. IRDP

C. HSRP

D. STP

View Answer

Q8. Which information does the subordinate switch in a switch stack keep for all the VLANs that are configured on it?

A. VLAN database

B. DHCP snooping database

C. spanning trees

D. routing information

View Answer

Q9. CORRECT TEXTYou have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram.

You need to configure SwitchC so that Hosts H1 and H2 can successfully ping the server S1. Also SwitchC needs to be able to ping server S1.

Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links. Company policies forbid the use of static or default routing. All routes must be learned via EIGRP 65010 routing protocol.

You do not have access to RouteC. RouterC is correctly configured. No trunking has been configured on RouterC.

Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution:

u2013 10.10.10.0/24

u2013 190.200.250.32/27

u2013 190.200.250.64/27

Hosts H1 and H2 are configured with the correct IP address and default gateway. SwitchC uses Cisco as the enable password.

Routing must only be enabled for the specific subnets shown in the diagram.

Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learned via the EIGRP routing protocol.

View Answer

Q10. Which SDM template is the most appropriate for a Layer 2 switch that provides connectivity to a large number of clients?

A. VLAN

B. default

C. access

D. routing

View Answer

Q11. Which command would a network engineer apply to error-disable a switchport when a packet-storm is detected?

A. router(config-if)#storm-control action shutdown

B. router(config-if)#storm-control action trap

C. router(config-if)#storm-control action error

D. router(config-if)#storm-control action enable

View Answer