New Questions 4

When a private VLAN is configured, which mode must be configured as a router facing port?

A. isolated

B. promiscuous

C. community

D. host

View Answer

New Questions 5

What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives 802.1d BPDU?

A. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives an 802.1d BPDU, it responds with an 802.1d BPDU and eventually the two switches run 802.1d to communicate.

B. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.

C. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU.

D. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.

View Answer

New Questions 6

A network engineer must adjust the STP interface attributes to influence root port selection. Which two elements are used to accomplish this? (Choose two.)

A. port-priority

B. cost

C. forward-timers

D. link type

E. root guard

View Answer

New Questions 7

Network engineer want to use UDLD, what he need to consider?

A. udld is a non-propriety

B. udld is working with non cisco devices

C. udld is layer 1

D. udld can aggressively disabled the port after eight failed retries

View Answer

New Questions 8

A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?

A. Reload the new switch.

B. Restart the VTP process on the new switch.

C. Reload the VTP server.

D. Verify connected trunk ports.

View Answer

New Questions 9

An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?

A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.

B. Adjust the EtherChannel load-balancing method based on destination IP addresses.

C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.

D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.

E. Adjust the EtherChannel load-balancing method based on source IP addresses.

View Answer

New Questions 10

Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?

A. CDP is enabled by default and can be disabled globally with the command no cdp run.

B. CDP is disabled by default and can be enabled globally with the command cdp enable.

C. CDP is enabled by default and can be disabled globally with the command no cdp enable.

D. CDP is disabled by default and can be enabled globally with the command cdp run.

View Answer

New Questions 11

Which type of information does the DHCP snooping binding database contain?

A. untrusted hosts with leased IP addresses

B. trusted hosts with leased IP addresses

C. untrusted hosts with available IP addresses

D. trusted hosts with available IP addresses

View Answer

New Questions 12

What does the command vlan dot1q tag native accomplish when configured under global configuration?

A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.

B. It allows control traffic to pass using the non-default VLAN.

C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).

D. Control traffic is tagged.

View Answer

New Questions 13

After reviewing UDLD status on switch ports, an engineer notices that the." Which statement describes what this indicates about the status of the port?

A. The port is fully operational and no known issues are detected.

B. The bidirectional status of "unknown" indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.

C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.

D. The UDLD port is placed in the "unknown" state for 5 seconds until the next UDLD packet is received on the interface.

View Answer

New Questions 14

Which option is a benefit of using VSS?

A. reduces cost

B. simplifies configuration

C. provides two independent supervisors with two different control planes

D. removes the need for a First Hop Redundancy Protocol

View Answer