Q1. Refer to the exhibit.

What is the result of the SPAN configuration on a Cisco switch?

A. Configure a SPAN session to monitor the received traffic on interface g0/4 only for VLAN 3.

B. Configure a SPAN session to monitor the received traffic on interface g0/4 for all VLANs except VLAN 3.

C. Configure a SPAN session to monitor the received traffic on interface g0/5 only for VLAN 3.

D. Configure a SPAN session to monitor the received traffic on interface g0/5 for all VLANs except VLAN 3.

View Answer

Q2. Which type of information does the DHCP snooping binding database contain?

A. untrusted hosts with leased IP addresses

B. trusted hosts with leased IP addresses

C. untrusted hosts with available IP addresses

D. trusted hosts with available IP addresses

View Answer

Q3. Which VLAN range is eligible to be pruned when a network engineer enables VTP pruning on a switch?

A. VLANs 1-1001

B. VLANs 1-4094

C. VLANs 2-1001

D. VLANs 2-4094

View Answer

Q4. What is the default amount by which the hot standby priority for the router is decremented or incremented when the interface goes down or comes back up?

A. 1

B. 5

C. 10

D. 15

View Answer

Q5. A Cisco Catalyst switch that is prone to reboots continues to rebuild the DHCP snooping database. What is the solution to avoid the snooping database from being rebuilt after every device reboot?

A. A DHCP snooping database agent should be configured.

B. Enable DHCP snooping for all VLANs that are associated with the switch.

C. Disable Option 82 for DHCP data insertion.

D. Use IP Source Guard to protect the DHCP binding table entries from being lost upon rebooting.

E. Apply ip dhcp snooping trust on all interfaces with dynamic addresses.

View Answer

Q6. Refer to the exhibit.

The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?

A. Disable VTP pruning and disable 802.1q.

B. Update the VTP revision number.

C. Change VTP mode to server and enable 802.1q.

D. Enable VTP pruning and disable 802.1q.

View Answer

Q7. What is the maximum number of 10 Gigabit Ethernet connections that can be utilized in an EtherChannel for the virtual switch link?

A. 4

B. 6

C. 8

D. 12

View Answer

Q8. A network engineer configured an Ethernet switch using these commands. Switchone(config) # Spanning-tree portfast bpdufilter default

Which statement about the spanning-tree portfast feature on the switch is true?

A. If an interface is enabled for portfast receives BDPU, the port goes through the spanning-tree listening, learning, and forwarding states.

B. If an interface is enabled for portfast receives BDPU, the port does not go through the spanning-tree listening, learning, and forwarding states.

C. If an interface is enabled for portfast receives BDPU, the port is shut down immediately.

D. If an interface is enabled for portfast receives BDPU, the port goes into the spanning- tree inconsistent state.

View Answer

Q9. When you design a switched network using VTPv2, how many VLANs can be used to carry user traffic?

A. 1000

B. 1001

C. 1024

D. 2048

E. 4095

F. 4096

View Answer

Q10. Refer to the exhibit.

Users of PC-1 experience slow connection when a webpage is requested from the server. To increase bandwidth, the network engineer configured an EtherChannel on interfaces Fa1/0 and Fa0/1 of the server farm switch, as shown here:

Server_Switch#sh etherchannel load-balance EtherChannel Load-Balancing Operational State (src-mac): Non-IP: Source MAC address

IPv4: Source MAC address IPv6: Source IP address Server_Switch#

However, traffic is still slow. Which action can the engineer take to resolve this issue?

A. Disable EtherChannel load balancing.

B. Upgrade the switch IOS to IP services image.

C. Change the load-balance method to dst-mac.

D. Contact Cisco TAC to report a bug on the switch.

View Answer