Q1. Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?

A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.

B. Each device broadcasts periodic advertisements to all of its neighbors.

C. Each device sends periodic advertisements to a central device that builds the network topology.

D. Each device sends periodic advertisements to all IP addresses in its ARP table.

View Answer

Q2. Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?

A. promiscuous port

B. isolated port

C. community port

D. trunk port

View Answer

Q3. An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?

A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.

B. Adjust the EtherChannel load-balancing method based on destination IP addresses.

C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.

D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.

E. Adjust the EtherChannel load-balancing method based on source IP addresses.

View Answer

Q4. What is the default interval at which Cisco devices send Cisco Discovery Protocol advertisements?

A. 30 seconds

B. 60 seconds

C. 120 seconds

D. 300 seconds

View Answer

Q5. RSPAN has been configured on a Cisco Catalyst switch; however, traffic is not being replicated to the remote switch. Which type of misconfiguration is a cause?

A. The RSPAN designated VLAN is missing the remote span command.

B. The local and remote RSPAN switches are configured using different session IDs.

C. The local RSPAN switch is replicating only Rx traffic to the remote switch.

D. The local switch is overloaded with the amount of sourced traffic that must be replicated to the remote switch.

View Answer

Q6. Refer to the exhibit.

What is the result of the SPAN configuration on a Cisco switch?

A. Configure a SPAN session to monitor the received traffic on interface g0/4 only for VLAN 3.

B. Configure a SPAN session to monitor the received traffic on interface g0/4 for all VLANs except VLAN 3.

C. Configure a SPAN session to monitor the received traffic on interface g0/5 only for VLAN 3.

D. Configure a SPAN session to monitor the received traffic on interface g0/5 for all VLANs except VLAN 3.

View Answer

Q7. Refer to the exhibit.

Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?

A. switch1

channel-group 1 mode active switch2

channel-group 1 mode auto

B. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode passive

C. switch1

channel-group 1 mode on switch2

channel-group 1 mode auto

D. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode auto

View Answer

Q8. A network engineer is setting up a new switched network. The network is expected to grow and add many new VLANs in the future. Which Spanning Tree Protocol should be used to reduce switch resources and managerial burdens that are associated with multiple spanning-tree instances?

A. RSTP

B. PVST

C. MST

D. PVST+

E. RPVST+

View Answer

Q9. which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?

A. portfast

B. port-security

C. spanning tree

D. storm control

View Answer

Q10. A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to

spike during peak working hours. What is the root cause of this issue?

A. The VLAN receives additional frames from neighboring switches.

B. The SDM VLAN template causes the MAC address-table to overflow.

C. The VLAN template disables routing in hardware.

D. The switch needs to be rebooted before the SDM template takes effect.

View Answer