Q1. Which three steps are required to configure a SIP trunk on Cisco VCS towards cisco unified communications manager? (Choose three)

A. Configure a neighbor zone that contains the Cisco Unified Communications Manager.

B. Configure a route pattern zone that contains the Cisco Unified Communications Manager.

C. Configure a transform that converts numbers to appropriate domains.

D. Configure a SIP trunk with Cisco Unified Communications Manager destination IP addresses.

E. Configure a search rule to route calls to the Cisco Unified Communications Manager neighbor zone.

F. Configure a SIP trunk security profile.

View Answer

Q2. Refer to the exhibit.

If an IP phone in San Jose roams to New York, which two IP phone settings will be modified by Device Mobility so that the phone can place and receive calls in New York? (Choose two.)

A. The physical locations are not different, so the configuration of the phone is not modified.

B. The physical locations are different, so the roaming-sensitive parameters of the roaming device pool are applied.

C. The device mobility groups are the same, so the Device Mobility-related settings are applied in addition to the roaming-sensitive parameters.

D. The Device Mobility information is associated with one or more device pools other than the home device pool of the phone, so one of the associated device pools is chosen based on a round-robin load-sharing algorithm.

E. The Device Mobility information is associated with the home device pool of the phone, so the phone is considered to be in its home location. Device Mobility will reconfigure the roaming-sensitive settings of the phone.

View Answer

Q3. Which two statements regarding IPv4 Static NAT address 209.165.200.230 has been configured on a VCS Expressway are true? (Choose two.)

A. The Advanced Networking or Dual Network Interfaces option key has been installed.

B. VCS rewrites the Layer 3 source address of outbound SIP and H.323 packets to 209.165.200.230.

C. VCS applies 209.165.200.230 to outbound SIP and H.323 payload messages.

D. With static NAT enabled on the LAN2 interface, VCS applies 209.165.200.230 to outbound H.323 and SIP payload traffic exiting the LAN1 interface.

View Answer

Q4. Which component provides a list of Cisco Unified Communications Manager node addresses that allow the phone to register to the cluster?

A. DNS option 150

B. DHCP option 150

C. DHCP option 66

D. configuration file from TFTP server

E. Primary Cisco Unified Communications Manager node from configuration file additional nodes during registration.

View Answer

Q5. Which option best describes a service that assembles a network model from configured locations and link data in one or more clusters?

A. LBM Hub

B. LBM

C. Shadow

D. Weight

View Answer

Q6. Which two items must you configure in Cisco Unified Communications Manager to deploy Cisco SAF? (Choose two)

A. an MWI

B. voicemail ports

C. a security profile

D. a forwarder

E. a remote destination profile

View Answer

Q7. An engineer is performing an international multisite deployment and wants to create an effective backup method to access TEHO destinations in case the call limit triggers. Which technology provides this ability?

A. AAR

B. CFUR

C. LRG

D. SRST

View Answer

Q8. An engineer must resolve a call failure issue. When using RTMT, the engineer notices that the Location Bandwidth Manager-OutOfResources counter is showing a positive value. Which option is the cause of the call failure?

A. lack of audio bandwidth

B. lack of video bandwidth

C. lack of transcoding resources

D. lack of audio or video bandwidth

E. lack of conferencing resources

View Answer

Q9. While troubleshooting a connectivity issue between Cisco Unified Communications Manager,

Expressway-C, and Expressway-E, an engineer sees this output in the Expressway-E logs.

Event=u201dAuthentication Failedu201d Service=u201dSIPu201d Src-ip=u201d10.50.2.1u201d

Src-port=u201d25723u201d Detail=u201dIncorrect authentication credential for useru201d

Protocol u201cTLSu201d Method=u201dOPTIONSu201d Level=u201d1u201d

What is the cause of this issue?

A. The Expressway-C Traversal Server username/password do not match the Expressway-E Traversal Zone username/password.

B. The Expressway-C Traversal Client username/password do not match the Expressway-E Traversal Server username/password.

C. The Expressway-C Traversal Zone username/password do not match the Expressway-E Traversal

Zone username/password.

D. The Expressway-C Traversal Zone username/password do not match the Expressway-E Traversal Client username/password.

E. The Expressway-C Traversal Server username/password do not match the Expressway-E Traversal Client username/password.

View Answer

Q10. When considering Cisco Unified Communications Manager failover, how many backup servers can be configured in a Cisco Unified Communications Manager Group?

A. 1

B. 5

C. 2

D. 4

E. 3

F. 6

View Answer